ToLanbbt 10Ft/3.05M Universal Garage Threshold Seal Strip with 300ml Black Sealant/Adhesive, Garage Door Bottom Weatherproof Strip Rubber DIY Weather Stripping Replacement(Blue)

Took a long time to straighten it out to lay it flat

Works as we we hoping it would

Was easy to install on an uneven floor surface and used in conjunction with a new bottom seal on the garage works for sealing under garage door gaps. Keeps my shop warmer.

well made. keeps runoff out of garage.

Bas de porte de garage,super materiaux tres bonne qualité tres bon coupe vent MERCI.

Worked great even on a wood floor. Fit perfectly

Item was alittle late due to weather but that was to be expected. Easy install, we’ll see if it keeps the water out of the garage. Fingers crossed!

You cannot find an easier way to stop your garage door leakage. This is a high quality product that is easy to install. Very effective, just line the threashhold right behind the bottom of the garage door so that the rubber bump covers any possible gaps between the door and the concrete porch. Highly recommended!

I have revised my review from 1 star to 4 stars. I took the chance and installed it. (Sorry if getting long)There were no guarantees but I ended up using Gorilla Construction Adhesive. The recent installation just withstood the tail end of tropical storm Beryl and a fierce thunderstorm that flooded the streets and driveway …. no hint of water in the garage. Normally there would be puddles, but ...Dry! Not even dampness.I have a double car garage that is 16 feet across with some low spots under the door slope inward. (Note: The garage is being used as a gym so a car seldom enters and the seal installation has not seen a winter yet. The concrete may have been sealed 15 years ago and perhaps this could make a difference.)1. I let the EPDM rubber seal sit for a couple of months laying flat with weight on it to relax the curl at one end that was a result of the tight roll in packaging. It never fully laid flat on its own even with heat and a 50 pound weight. It was a little longer (16.5') than I needed so I could cut most of the curl out and the glue held it flat.2. Placed the seal along the door and trimmed it to get a rough fit using metal shears and knife. Trimmed it to fit around roller track. Cuts easily.3. Cleaned the concrete with Rustoleum heavy duty concrete cleaner scrubbing full strength with nylon brush (glasses, kneepads and heavy rubber gloves). Wiped and rinsed it well. Let dry for nearly 2 days with temperatures in mid 80’s.4. Placed the seal along edge of garage door so that it was just snug. Raised and lowered door to check fit. Had to do some fine trimming. (I used a laser level to get it straight. My door was straight so this worked well, but in some cases it may be prudent to push it forward to ensure a seal with door.)5. Used 1.5” masking tape along both sides. (This did help, but not as clean as with a silicon bead or paint.) It also provided a guide to place it down.6. Cleaned back of rubber seal with TSPe liquid organic degreaser and let dry, then wiped with 90% alcohol using clean cloth.7. Applied bead of Gorilla Construction adhesive on concrete about a quarter inch inside each edge and then did a zig zag pattern between beads. You have 10-20 minute working time. Not a big rush, but worth noting. (Was using thin vinyl gloves at this point.) Used one complete tube 266ml had a second one on hand.8. Had two helpers holding the seal like a big snake. I placed one end down and carefully placed it between the masking tape over the whole length. Then went along length carefully adjusting and pressing firmly down by hand, pressing glue out to edges. I got some on my gloves that transferred to seal, however with some paper towel it wiped off; Gorilla glue says alcohol will clean. Should have put on fresh gloves.). Then stepped along length pressing out air bubbles (can use board to keep off shoes); a little more glue came out. It was still very workable.9. Let dry for about 5-10 minutes and lifted masking tape. (Not perfect, but wiped off rubber and used scraper for some very minor seepage.) I could only get white Gorilla Construction Adhesive and it dries white, but overall it looks very good.10. Put garage door down and left for 48 hours.11. Used Mono Silicon Max clear caulk liberally at seal ends from door frame to rails and around seal to ensure no water could make its way around or under.So far it is good.The -ve, Why not 5 stars: The manufacturer/seller provided no adhesive recommendations. The tight roll in the packaging caused a permanent curl that fortunately I was able to cut mostly out and glue flat. It has not seen a winter or traffic. Initially working well but I cannot evaluate the long term performance.The +ve, Why four stars: It is heavy duty, lies flat and has formed a good seal. At this point it is securely attached to the floor. It looks good. The garage is perfectly dry even after two very heavy rain storms that were pounding on the door. It was worth trying because it was easier than cutting a drain, using leveling concrete, or re-pouring the garage.(Original Review 1 star: EPDM is a very tough synthetic "rubber" and the EPDM seal itself is flexible, tough, good thickness. The problem is that the seller does not recommend or supply an adhesive and finding an available adhesive certified to glue EPDM to concrete has proved to be impossible. EPDM is no ordinary "rubber". The number of reviews that mentioned leaks (with pictures) under the threshold seal was a flag for me to research. I did see reviews that said check that the glue says for rubber, but rubber does not mean EPDM specifically. Several users recommended Loctite Fuze It or Poly Urethane type construction adhesives or better preparation. I went to the manufacturers technical spec sheets. Liquid Nails Fuze It Max (LN3000) states "good for rubber and concrete" BUT BUT under limitations specifically says "NOT recommended for polyethylene, polypropylene, Teflon..... EPDM....., or TPO." Construction Adhesives such as PL Premium® MAX Construction Adhesive state concrete but under limitations say "Some materials such as rubbers and plastics may have bonding difficulties" along with other substances such as propylene. I did find some solvent adhesives that are not available in many states and Canada or others would not be suitable for this application. I am now very hesitant to install the EPDM threshold seal given the adhesive manufactures warnings and listed limitations. )

Huge difference! My garage floor/door seal had some small gaps, but those small gaps can add up to a large leak. I have heat and AC in my garage and I have noticed a huge difference with this in place.Lay out the seal strip for a few hours to let it flatten out as it is shipped coiled. Then measure, cut, mark/clean your floor, put down the adhesive, lay the strip down and close your garage door for 24 hours. It will help immensely to have two extra sets of hands to get this down. Two people can do it, it is just easier with three.Instructions were clear and easy to follow. Well worth the money!

Rise is enough to keep water out

After leveling up my concrete floor and cleaning, it would have been very disappointing to have a poor result. To my satisfaction, this does the job. The door is sealed from cold, leaves, water, and pests. If you prepare the surface, you won't be disappointed. How long it lasts is the only other question now.

Me gustaria que hubiera sido más alto, para que amortiguara un poco mas el peso de la puerta