Your cart is empty.
Your cart is empty.
Polarity:Color band denotes cathode
Terminals:Axial leads, solderable per MIL-STD-202
Package Quantity:
5 Pcs x Rectifier Diodes 6A10
10 Pcs x Rectifier Diodes 10A10
5 Pcs x Rectifier Diodes 20A10
Michael gagnon
Reviewed in Canada on January 5, 2025
Empêcher le.courent de revenir
bigdan911
Reviewed in Canada on June 17, 2024
Needed these on my harness, did the job great
eric
Reviewed in Canada on October 5, 2024
Très bien
Raydawg
Reviewed in the United States on October 15, 2024
Great having spare parts for trial on our projects
steve hamilton
Reviewed in Canada on January 24, 2024
good
Rabon schall
Reviewed in the United States on August 19, 2023
Exactly as described
John Beatty
Reviewed in the United States on July 4, 2023
I have used only one, but it does what a diode ought to do! Great value too. I have it on the excitation lead on a farm tractor alternator - lots of vibration and heat, and so far 100%!
Customer
Reviewed in the United States on May 9, 2023
Worked great at replacing a 30 year old diode that decided to leave by smoke.
Luis santiesteban
Reviewed in the United States on March 25, 2023
Muy orijinales los iodos muchas gracias
Robert
Reviewed in the United States on February 28, 2023
Diodes checked OK. I haven't used any yet. In parts box till needed.
Marvin
Reviewed in the United States on November 9, 2023
Oh I purchased them them and stored them. I got to test them with a regular meter and they checked out ok. I have been working on an energy harvesting design of mine and used two of them I am working with very very low amounts of energy pulsed to a higher voltage ad then "rectified" before stored on a rechargable battery. All the components have tested ok but I had trouble charging the battery. The energe was being produced and it actually got to the battery and was charging it but at the end of the day the battery had lower charge than expected and then dead overnight. I tested a different battery with the same result. I put the whole thing in the Oscilloscope and I clearly see the pulse of energy reaching the battery but I was not getting anywhere. then I increased the signal to one amp and put the thermal imager on the cuircuit when I noticed the Diodes were getting warm. hmmm I pulled them both off and tested them again and checked out OK but I know they should not be getting warm with just one amp. I tested their resistance and with two meters and it was all over the place. I mean their resistance was changing rapidly up and down. Then I realised why the batteries were not holding the charge! Reversr voltage leakage. I replaced the batteries with a capacitor to see a quicker response and tested again. The pulse of energy charges the Capacitor and inmediatelly begins to discharge. I replaced these rectifiers with two used ones from a previous project, they were just laying around and Bingo Problem solved. I tested other rectifiers from this same batch and they too have a reverse leakage. Moral of he story? they are useless for my project. I have no idea how hot would they get if I pushe 5 amps or ore through them either but being to low in price I dont think I will complain much. I got what I paid for. I guess they could be used for a power supply but then again they would probably waste a lot of energy while its turned on. Dont assume these are good if the meter said they are ok, check the reverse leak and under load to see if they will hold up to the claim. thank you
Customer
Reviewed in Canada on December 12, 2021
Remplacer une d’iodé défectueuse par celle là fonctionne très bien
MV
Reviewed in the United States on November 4, 2021
170° F. with 3 AMP through the 20 AMP diode
Recommended Products
