Your cart is empty.
Your cart is empty.Product Description
TF Micro SD To SD Card Extension Cable Adapter Flexible Extender For Car GPS
Features:
100% Brand New and High Quality
Push-Push SD slot.
Support all size 16GB, 32GB 64GB 128GB SD / SDHC card.
Compatible with GPS, DVD, DVR, LED/LCD screen, or mobile phone Smartphone etc.
Total Length: 53.5cm Cable Lenght: 46cm
Material: Plastic+FFC
Quantity: 1 Pc
Net Weight: 20g
Where can use?
Convenient to test many SD memory-cards on any electronic device which supports MicroSD(TF) memory card,PDA,smart phones, MP3, MP4.Digital Camera ,GPS.
Also used as extender or Linker when your device has built-in Micro SD Memory Card Slot and you need to extend it outside to use Bigger SD Memory Card.
R D. Grayson
Reviewed in the United States on August 5, 2024
It saves me from wearing out the port on my 3D printer and lets me use the stack of older full-sized SD cards I had left over.
Space_shelf8
Reviewed in Canada on July 3, 2024
Works great with a Bambu 3D printer, which uses a micro SD card slot. Didn't want to repeatedly wear out the micro SD slot on the printer so got this. Also, it's much easier to use a full sized SD card vs the micro when transferring files. A great upgrade and good quality, no issues with connectivity after multiple prints. Would recommend!
Jacques
Reviewed in Canada on October 27, 2024
prfait pour un bricoleur
Kindle Customer
Reviewed in the United States on October 21, 2024
It works, sort of. Connections won't click in positively so had to manuall hold the cable while using.
Fast eddie
Reviewed in the United States on August 3, 2023
WOW, if you have an Elegoo Neptune Pro 3, you need this adaptor. Had a hard time getting the micro sd card into the slot, dropped numerous times and had to use a flashlight to see the opening. Simple to install; plug the small end into micro sd card slot, run flat cable under the printer, using two (2) sided tape attach the boss end adjacent to the screen. Tips: make sure to use a 8 or 16 gig standard sd card. Attach opening of the SD card receptacle on edge of printer to allow removal of the card.
SmokinJoe
Reviewed in the United States on August 19, 2023
Nothing much I can say other than I bought this to remote-mount a camera, but the camera doesn't recognize the SD Card with the extender in between. Camera works fine without it. And I can't even get my money back. Avoid.
Roy & Beth
Reviewed in Canada on December 22, 2023
Bought this because my 3D printer has the micro SD card in the back and it's a pain to install and remove it. I plug this into the micro SD slot and then place it at a more convenient location. It didn't matter to me that it is micro SD to standard SD as being an adapter was not what I wanted it for. Saving my printer files on a micro SD or full size SD is irrelevant. I only wanted the convenience of bringing the slot to a better location.There is one downside though that prevented a 5 star review. And that is when you remove the SD card and reinsert it again, the card is not recognized. I have to power down the printer and power it back up again to recognize the newly inserted card. But that is less of a pain than reaching behind the printer to find the micro SD slot. So I'm still very happy with it.
Neal W.
Reviewed in the United States on March 6, 2022
The inherent issue of card not seen or not recognized when its plugged in permanently with cover is a pain in the kiester.... but it will do what you want if you power cycle the printer evey time you insert or take out a card .This is the same issue I have with sd card adapter on my laptop but I can pull the adapter easy enough.
Jennifer Janes
Reviewed in Canada on August 3, 2020
No issues, works like it should.Not much else needs to be said.
J S
Reviewed in Canada on October 31, 2020
Works good and its long enough to reach glove box from the radio
leon jones
Reviewed in the United States on August 27, 2019
Loses connection mid print, so unusable for my application.
Christian.glahn
Reviewed in the United States on June 14, 2018
This has a great quality build feel and I really like that. It works well for Raspberry Pi, only problem is that the microSD end is quite a bit longer than a standard SD, and this provides a lot of leverage which could damage the SD slot, if not handled properly.
Steve_in_TN
Reviewed in the United States on April 26, 2018
Hello All, It's Steve@HobbyADHD With Another Review!This product has been a great addition to my 3D printer. I haven't disconnected it since the day I received it and it's been working great. A must have if you need an adapter.Construction: Very sturdy. The cable is thick and the casing on the SD card slot is beefy.Fit: Solid connection.Usability: Works great on my 3D printer.Issues: NonePros: Works every time Solid constructionCons: NoneI would highly recommend this product if you have a 3D printer that uses microSD cards. It works perfectly and gives a needed SD card slot for my Anet A2 3D printer.
Recommended Products