Your cart is empty.
Your cart is empty.Product Description
Gmoney$$
Reviewed in the United States on October 27, 2024
Controlled temperature and humidity well for a long time and then failed. Easy to program, I have several.
🐸 Lover
Reviewed in the United States on October 14, 2024
UPDATE 10/2024Mfgr emailed me about my issue and replaced it quickly with few questions asked AND even followed up with me. Great service.At first this unit was perfect. My frog was happy and I was happy. Then, one day, I noticed the fogger wasn’t going off at all. I checked the unit and it was stuck at 39.9F and 0% RH. I’ve tried turning it off, reprogramming etc. to no avail. If the mfgr will send me another I’d change my rating. I would even be willing to ship this one back. Will update if/when it’s resolved 😕
Michael D
Reviewed in the United States on April 17, 2024
The only complaint I have about it so far is that the instructions are almost mandatory - but are written very poorly.Mines almost a year old (only used for about a month) and when setting it back up I obviously couldn't find the instructions. You can figure out what each setting does, but it would be nice if there were a sticker on the back of it that explained everything clearly.On thing I see a lot of complaints about is that it continually beeps on high humidity.H_L needs to be equal to H_H if you want to disable the High humidity alarm.By default H_L = 10 and H_H = 99. As soon as the humidity goes above 89.9% you will hear a continuous beep.I lowered the H_H down to 10.0% and the alarm stopped. (I did it this way because it was taking too long to get up to 99%).With all of the complaints and low reviews I am shocked they have not tried to update their instructions or reply to the users with this complaint (I actually came here to write the same review until I randomly got the idea to try matching H_L & H_H after reading the comments.)
Nic.k
Reviewed in Australia on July 27, 2023
Great for my Marta tent set up. Happy outcome
Janelle Wilson
Reviewed in the United States on May 29, 2023
I used this for my mushroom fruiting chamber. Set it up and used it for a little over an hour before it stopped working correctly, started beeping and an error message code for EEE came up (this error is not included in the instructions that it came with). I contacted the seller and they immediately refunded my money. Stated there is an "issue" with the product and did not want to send another one. I'm giving it 2 stars only for the sellers prompt attention, honesty and refund but I would not recommend anyone purchase this for a mushroom fruiting chamber or other high-humidity environments.
Jason Adam
Reviewed in the United States on May 1, 2023
Better price than Inkbird controllers, works well! I got two of them, one worked great, the second had a faulty humidity sensor. The seller was very responsive and took care of the issue very quickly. Very happy with Pymeter, and happy to keep my gourmet mushrooms humidified!
Hannah Drew
Reviewed in the United States on October 15, 2023
Update: I went ahead and used the humidity control while I'm in my office and can keep an eye on it. Bad idea. Appears that it has shorted out my humidifier.First issue I had to plug and unplug the device a couple times before I could initiate the setup process. The first few times it just displayed an 8 instead of the step menu.Once I was able to setup the ranges, which was easy enough I plugged in my humidifier to rest it out.It turned on the device as expected but after about 3 minutes it displayed a 6 on the screen and nothing else. I thought that might be the operation screen. Nope, unplug and plugged back in, showed the ranges and it allowed the humidifier to run past its set range.I don't trust this device at all. Not reliable quality.
Honest Opinion
Reviewed in the United States on January 28, 2023
Forget inkbird, and get this. It's cheaper, easy to setup, smaller footprint.I didn't bother to figure out alarm settings, and just removed the speaker inside. It's really simple to do. Use a fingernail and pull the 6 silicon/rubber plugs out of the back plate. Remove 6 Phillips head screws beneath them. Remove backplate. You'll see a circuit board mounted by two more Phillips screws, Remove those also. On the other side at the very top is the speaker. It's the black round plastic thing with a hole in the center. Attaches to the circuit board with two legs and are soldered. I desoldered it, closed it up, and it won't beep EVER now.Setting the temperature and humidity couldn't be easier. There is also calibration for temp and humidity towards the end of settings menu. Having hygrometers handy helps with calibration also. Just be sure to give the hygrometer time to adjust, because the pymeter is SENSITIVE and ACCURATE!
Renee
Reviewed in the United States on April 10, 2023
This thing worked until today now sensor won’t read humidity and it shut off. Can’t return it because return window closed April 4. Not happy. My frog was pressed up against the glass trying to get out. It woood have killed him if I wasn’t home.
Recommended Products