Your cart is empty.
Your cart is empty.The Tekonsha Prodigy Brake Control Mounting Pocket Kit allows you to remove and store your brake control when not in use. The Prodigy Brake Control Mounting Pocket Kit is compatible with the Prodigy or Prodigy P2 Brake Controller; It is NOT compatible with the P3 Brake Controller. The pocket kit includes mounting hardware and wire connectors. The Prodigy Brake Control Mounting Pocket Kit comes with a limited 1-year warranty. Since the 1970s, Tekonsha has been at the forefront of innovation and design, with products ranging from brake controllers to electrical wiring and trailer brakes.
Customer
Reviewed in Canada on October 17, 2024
.
Paul Kurtz
Reviewed in the United States on July 26, 2022
Needed a new mount for my Prodigy P2. This housing fits right into the pocket of my center console pocket in my truck to secure the unit. Works great.
charles
Reviewed in the United States on February 16, 2021
Just what I needed to help transfer my controller between vehicle's
Rick
Reviewed in Canada on April 3, 2021
Works as expected
AJH
Reviewed in the United States on March 20, 2020
I have a breaker controller in my SUV and wanted to use the same unit in my RV. Works as designed. Mission accomplished
TJ Hep
Reviewed in Canada on June 5, 2019
worked perfect, easy to mount
Customer
Reviewed in the United States on June 12, 2019
was the correct one easy to install
Leita Stevens
Reviewed in the United States on February 5, 2018
Easy to install, tidy appearance, and keeps the unit secure.
Customer
Reviewed in Canada on May 25, 2017
Fit my unit perfectly and super fast shipping
jwl80303
Reviewed in the United States on February 11, 2017
As others have noted... The P3 does not fit into this mounting pocket without some slight modification to the pocket itself. At the rear of the pocket, there is a little 'step' in the plastic to provide clearance for the connecting cable plug for whatever unit is intended to go into this pocket. But it's not enough for the P3 -- its plug is further to one side (the wrong side) and once the connecting cable is attached the P3 will not slide all the way into the pocket. You must shave off an approximately 1" x 1/4" piece of plastic from the rear in order to provide clearance for the connecting cable and its plug. I used a utility knife with sharp blade and removed the material a sliver at a time, took about 10 minutes to remove enough to allow proper clearance. Also the two clips on either side of the mounting pocket do not align with the two holes on either side of the P3 -- not even close. That doesn't seem like it will be a problem -- the P3 seems to be held quite securely in the pocket just from friction alone. I'll be mounting mine with the P3 facing upward, so gravity alone will be good enough for me. This pocket is -- in my view -- far better than either bracket that came with the P3, if for no other reason that it has an approximately 3" x 2.75" flat surface where I'm going to attempt to use sticky-back velcro to mount it to the car. I really don't want to put screw holes into my nice new car if I can avoid it. Time will tell. I'd give it 5 stars, but will deduct one for Tekonsha's failure to provide a bracket that exactly fits the P3
Customer
Reviewed in Canada on December 30, 2016
Just as described Fit my p2 perfectly.Thanks
Chuck J
Reviewed in the United States on May 27, 2015
Holds my Tekonsha P3 just fine. Wanted an additional mount for my second vehicle. The description didn't say that the P3 would fit, but for the price I thought I'd give it a chance. Works perfect.
Jon
Reviewed in the United States on March 12, 2015
This mount is a lot sturdier and easier to mount than the plain strap type mounts that usually come with brake controllers. and the snap in feature makes it easy to use the same brake controller in more than one vehicle.
Recommended Products
