Your cart is empty.
Your cart is empty.09044 Features: -Range cord.-Thick vinyl insulation with right angle male plug.-Four conductor, round cord.-Strain relief clamp helps prevent cord damage.-SRDT wire type. Includes: -Hardware included. Color/Finish: -Color: Black. Specifications: -6/2 and 8/2 Wire gauge / conductor.-45 Amps.-Voltage: 125/250 V rating. Dimensions: -Depth: 48".
Jeff
Reviewed in the United States on February 6, 2025
Your can use this to install a Tesla Wall charger without having to hard wire it directly. Plenty of YouTube videos to document the steps. I've had this installed for over 6 months without issue. BUT you MUST lower your amps to 40a . Don't charge on max or you'll burn it out after a few months.
JR
Reviewed in the United States on March 8, 2024
I used this to convert my free hard wired Tesla Wall Connector to a plug in EVSE into a NEMA 14-50R reciprocal. I used a 3/4 cable gland for strain relief and SET THE TESLA WALL CONNECTOR TO 40 AMPS MAX! Be aware that a 14-50 whip to a hardwired charger may not be code compliant.
John W. Ostergren, Jr.
Reviewed in the United States on November 8, 2024
Uses #6 copper wire. 3#6 conductors and ground appears to be #8.
Robert Johnson
Reviewed in the United States on June 17, 2023
I was looking to convert a hardwired Juicebox EV charger to a plug-in charger with a NEMA 14-50 plug. This product fit my needs perfectly. The two hot conductors are 6 awg and capable of carrying 50 amps. The plug is sturdy and fits easily into the 14-50 receptacle. My EV charger reconfiguration project was a success.
SK
Reviewed in the United States on December 28, 2023
I clipped the ends off and used it fine with a Tesla Wall Connector. Be sure to twist the strands well before putting them in the terminals - they're finer than the kind of wire you'd hardwire with, so they'll tend to fan out under the screw and slip out to the sides. Otherwise, follow Tesla's instructions, including looping the cable and securing it with a zip tie. Be sure to use a 3/4 cable gland for strain relief and SET YOUR CHARGER TO 40 AMPS MAX! This cable is rated 50 amps, but for continuous loads like charging a car, code requires an 80% derate for safety due to heat build up... the default setting on Tesla chargers is 48 amps. Adding a 14-50 whip to a hardwired charger isn't code compliant anyway, but you'd be a fool not to abide by the 80% rule.
Yang Chun Lun
Reviewed in Canada on July 13, 2021
works great replacement for my stove
Customer
Reviewed in the United States on June 7, 2021
Bought this pigtail for my blink hq100 charger. Worked fine, but the length of wire after the cladding was an inch too long and I had to do some bending to make it all fit. Also the ends are a little too wide, so I had to crimp them down a little. Sorta pain. Also you’ll want to pick up a 1” romex connector since a spare doesn’t come with this it the blink charging station. You’ll also find that the charger doesn’t have separate ground and neutral leads, so you’ll have to tie them together since this is 4-wire. Maybe rethink what plug and receptacle you want if you only really need 3 wire!
Scott B.
Reviewed in Canada on May 31, 2021
Fast shipping, works well.
Harvey Hovelkamp
Reviewed in Canada on September 20, 2020
It was the right length for my project of wiring in a 50 amp rv generator power supply.
dbmemphis
Reviewed in Canada on December 4, 2020
Perfect. Isntall was a piece if cake and cheaper than big box stores. Good stuff
Hazard
Reviewed in Canada on December 11, 2020
Bought this to use with my Tesla wall charger (to avoid having to hardwire the charger). Used various online resources and tutorials, combined with the directions that came with the wall charger. Been working well with no issues for about 6 months now.
EastAL
Reviewed in the United States on March 27, 2019
Worked well to install on my new range, and the 4' length was perfect - not too much slack to bind up under the appliance. My one suggestion would be to strip a bit more of the black outer insulation off since for ranges with 4 terminals you need a bit more flex to bend the 4 conductors (especially the ground) to fit the 3 main terminals and the chassis ground.
BigJim
Reviewed in the United States on March 25, 2019
I think this is a very high quality item. I have had many of the competing brands. I have found this to be Superior and durability and the I thought that was put into the way it was made. It seems that detail was paid even to the smallest of items in it's creation and production. Anyone who has put in a large number of these will be able to pick out many features that this has that it's competition Lacks.
Recommended Products
