Your cart is empty.
Your cart is empty.Product Description
-
Perfectly fit with 2018-2025 Jeep Wrangler JL 4 Doors
-
Constructed with 2 layers coated carbon steel which ensuring long-lasting performance.
-
Bearing 550lbs without bending.
luis melgar
Reviewed in the United States on January 1, 2025
Once again the instructions are worthless. It took me about 15 minutes each side give or take should take no more than 30 minutes to complete the process.
Matt C
Reviewed in the United States on September 25, 2024
I agree with most that the instructions and video are extremely lacking!! 3 size bolts, the largest of which has 12 bolts, 24 flat washers, and 12 lock washers, these secure the running board to the bracket. The mid sized bolt, which has 6 bolts, 6 flat washers, are used to secure the bracket to the bottom of the body, then lastly there are 12 small bolts with 24 flat washers and 12 lock washers, these are to secure the bracket to the pinch welds, the head of which will face out towards you when your looking at your vehicle from the side. Once I sorted that out which didn’t take long it took me under an hour to secure both sides. Very sturdy and compliment my jeep quite nicely.
Gavin
Reviewed in the United States on August 30, 2024
Love the look, easy to install once you figure it out. Basically no instructions, but if you have common sense and watch the video you can figure it out. Not enough nuts and bolts to be consistent with regards to size. Great Product for the price. Fits nicely.
homer k reyes
Reviewed in the United States on August 28, 2024
These are some very, very nice steps. These are well designed well-made the brackets fit perfectly and there’s no problem at all following how to put everything together. The only downside I would say is the instructions. Don’t really tell you or at least I couldn’t figure it out. what bolt she should use where so I ended up having to go get some more bolts because I wanted to use the bigger bolts and I ran out of those, and I thought that the bigger bolt should be used in more places and what they supplied that Other than that, everything is stamped and marked left and right and the brackets at Bolton to the Jeep were marked front metal and rear. Everything was very easy to put together all I would tell someone is to just bolt things up. Don’t tighten anything down get everything adjusted well and then go back and tighten everything up after you get it all put together, but I am really really happy with these steps and they look really nice
Kindle Customer
Reviewed in the United States on December 29, 2024
Looks great, easy to install
Bear
Reviewed in the United States on December 21, 2024
Looks sharp on Jeep. Very happy with how it looks.
Customer
Reviewed in the United States on November 26, 2024
The entire process took me 1 and 40 minutes solo, which included setting up, removing the old running boards, figuring out all of the hardware, and mounting. The instructions are completely garbage.For clarity:M6 set is for the alignment screwsM8 set is for mounting to frame (don’t use)M10 is for mounting the running boards to the bracketTools required:M6 = 10mm socket and 10mm wrenchM8 = 13mm socket and 13mm wrenchM10 = 16mm socketReference the picture I attached for setting up your bolts: bolt > spring washer > washer > (component you’re attaching to > washer > nutStart by removing the factory alignment screws with the 10mm socket. Then remove the mounting screws with the 16mm socket. Slide off old running board.Each new bracket is marked with location. Hand tighten each bracket into place (do not tighten with sockets and wrenches yet). Mount the running boards hand tight.To finish, with socket and wrenches, start by tightening the M8 mounting bolts, followed by the M6 alignment bolts, and finally the M10 running board bolts.Build quality is pretty decent. Out of the box there were a few very sharp slivers of metal protruding. Ask me how I found out. Everything fit into place pretty well, I did have to tighten one of the rear screws in order to get the second to fit for both rear brackets. There were also a few scratches that were removed some of the powder coating from transport or production. All in all, they are not bad. Definitely an improvement over the OEM and matches perfectly on my Oscar Mike. The center step is a nice added bonus as it allows plenty of access to the roof.Stars reflect lack of instructions, random metal filings, and the few scratches I found.
Dolores
Reviewed in the United States on October 25, 2024
The steps are great but the instructions for installing is a single page with 2 pictures od the Jeeps frame rails. Was also missing some hardware
Recommended Products