Your cart is empty.
Your cart is empty.Protect those expensive headlights, turn signals and parking lights from impact with the Rugged Ridge Euro Light Guards. Each Euro Light Guard is easy to install with no drilling required. Made of black powder coated for a true attention to detail.
Brendan B
Reviewed in Canada on April 24, 2019
Cheaply made rusty after one season and stain the jeep
Edward Wood
Reviewed in Canada on February 3, 2018
HAD TO RETURN DIDN'T FIT NEW GRILL
CRod United
Reviewed in Canada on June 2, 2017
Perfect Fit
LARRY SCIBECK
Reviewed in the United States on February 19, 2017
It is a bitch to get them on, and to get them off, to clean.
Mike1121221
Reviewed in Canada on May 13, 2016
Exactly what they are supposed to be. Installation instructions suck but it is very easy to figure out.
Terrence Ebare
Reviewed in Canada on June 21, 2014
Well made and looks good on my 2013 Jeep Rubicon. Install was fairly easy although I had to remove my front grill,took about a hour to install.
Jamie
Reviewed in the United States on March 1, 2014
Everything about the design is a positive. The metal is well finished and the paint looks good. The included instructions have text in addition to just pictures.To elaborate on the included directions I have included the comments below:The larger guards (for turn signal) have three tabs that line up with the light holder. These were slightly too tight to place over the corresponding area on the light assembly. Bending them out slightly allows the guard to be attached easier. The longest tab needs to be attached first and then the others. If you have bent out the tabs some be sure to press them back in after the guard is attached.For the smaller guard (side lights) the directions have you completely removing the assembly. I found it difficult to press the tab holding the lens to the fender assembly to perform this action. However, I found this removal unnecessary and was able to separate the two assemblies (fender flare and fender) enough to slide the guard into place.Overall time to install was less than 20 minutes.
Christina Graw
Reviewed in the United States on February 16, 2014
Easy to install and they look awesome. I love dressing up my Jeep with Rugged Ridge products I never really veer off from buying Rugged Ridge unless they don't have what I am looking for
Christopher
Reviewed in the United States on January 9, 2014
I bought these just to add a little flair to my Jeep Wrangler 2010 Sport Unlimited. I'm going for the maroon and black look, so I've been purchasing a fair amount of the Rugged Ridge products in black. For installation, as others have mentioned, the front turn signal guards were a piece of cake. Get under there, and pop two clips per light and they push right out the front. My main concern for these was that they don't seem to fit completely flat overtop the stock lights. Two of the clips barely reached over the notches and I found myself having to use needle nose pliers to crimp down two of the metal tabs to make sure they stayed. Once that was done though, they do look nice once mounted.As for the side fender flare guards, these were ALOT more work than they should have been. Not really any tools required, except for an allen wrench and alot of elbow grease! The worst part of the installation for the fender side guards is making sure you don't break the little prong that holds the light housing to the inside of the fender liner. This is easier said than done. Take your time with it, and don't rush. Once done, they look OK, but I think the blinker guards have more of an impact. Overall, the install took me approximately an hour and a half, but should have realistically taken me 30 minutes tops.I'm not upset with the purchase, but not thrilled either. If you're gonna use all the Rugged Ridge products, this might add something to the look, but if you're "just" using these, I'd say pass.
Roberto D Sabater
Reviewed in the United States on January 12, 2014
I installed these items for my 2013 Wrangler Sport S in less than an hour. The fender ones were a bit tricky, but not really a problem. They add a great detail to my car and I have received compliments. I highly recommend these for anyone looking to add a nice detail to their Wrangler.On a side note, beware that the Rugged Ridge 11230.01 head light grills do not fit the 2013 Wrangler headlights.
Rick Woodham
Reviewed in the United States on January 3, 2013
These light covers look great on wifes black Wrangler and were very easy and fast to install. Had installed fender flares on her Wrangler, so the the covers for the side lights were too small. This was not problematic as it looks great without guards on the side lights.
T. Madsen
Reviewed in the United States on November 22, 2012
This is a nice product. Seems well made and has a good durable finish. The funny thing though was that although these are Jeep Jk specific, they don't really fit that well and are difficult to get in place. You just sorta get them on the best you can and settle for the fit. The fit reminded me of a part made to fit many applications but didn't fit any exactly right. I would have liked these much better had they been a better fit. I would probably try a different brand if I had a do-over.
J. Rayhorn
Reviewed in the United States on May 9, 2011
I really like the Rugged Ridge black Euro guards (well-made, come in silver or black, etc.), but this set is not for a 2011 Jeep Wrangler. You can't get the "combo" pack for the front turn signals & side marker lights (that's what this is) - you have to buy them separately as and .BE WARNED: if you use the "Find parts that fit your vehicle" program on Amazon, it will tell you that these fit a 2011 JK. These may work great for earlier model Jeep JK (2007 thru 2010 maybe?), but they do not come close to fitting on a 2011 JK. You have to opt for paying about $13 more to purchase them both.I would give this item a 5-star rating except that it is the wrong item for a 2011 Jeep Wrangler JK.Amazon's little app usually gets it right, but it screwed the pooch on this one.
Recommended Products