Shopping Cart

Your cart is empty.

Your cart is empty.

R410A Refrigerant Charging Hoses, 60' AC Charging Hose 1/4' SAE to 5/16 SAE, Fits for R410 R32 Air Conditioning and HVAC Manifold Gauge Hose Kit (4000-800) PSI (3pcs)

Free shipping on orders over $29.99

$20.99

$ 10 .99 $10.99

In Stock

About this item

  • HIGH WORKING PRESSURE --- R410A AC Charging Hose Set Length 60‘', Working Pressure 800 PSI (it's higher than that of R134A charging hose (600 PSI), Burst Pressure 4000 PSI. Providing you safety and convenience to test or recharge many HVAC system.
  • UNIQUE DESIGN --- R410A Refrigerant charging hose set yellow hose both side are 1/4"SAE thread, but the red and blue hose are different, one side is 1/4'' SAE, another side features 5/16 SAE thread. A/C Charging Hoses with 45 degrees angle on the service port site for easier access.
  • APPLICATION --- Suitable for refrigerants R410A, R32 ECT that any with 1/4" & 5/16" SAE thread. Great for vehicle or home air-conditioning with highly working performance. Necessary tools for HVAC, air condition maintenance and coolant or Freon adding.
  • PREMIUM QUALITY --- 3PCS x 60" (1.5m) Manifold hose set was made of high-quality brass alloy and rubber for long term use, easy to operate and install, strong sealing for durability and safety.
  • WHAT YOU GET --- R410A HVAC refrigerant charging hose set have one year warranty. If you have any questions about our product, simply contact us to get a replacement or refund. We provide friendly 24/7 customer service.



Product Description

1

FEATURES:

  • 60-inch hose set color coded in red, yellow, and blue.
  • 800PSI working pressure and 4000 PSI burst pressure. For use in adding R410A, R32 refrigerant to vehicle or home air-conditioning with highly working performance.
  • A strong six-sided crimp provides a reliable connection between the hose and barb even at maximum pressure
  • The coupler nuts are deeply knurled for quick finger-tightening
  • Premium refrigerant charging hoses are built for long life and dependability
1
1

1

Unique Design:

  • Refrigerant charging hoses set designed to meet 1/4" & 5/16"SAE Requirement on both end of each hose for refrigerant permutation.
  • A/C Charging Hoses with 45 degrees angle on the service port site for easier access.

1

Specification:

  • Material: Brass and Rubber
  • Overall length: 1.5m/60 inch.
  • Connection: 1/4" SAE and 5/16" SAE Female (Red and Blue Hoses), 1/4" SAE Male and Female (Yellow Hose).
  • Rated working pressure: 4000 psi burst / 800 psi Max. working pressure.
  • Applicable Refrigerant: R410A, R32 that with 1/4" SAE and 5/16" SAE thread.

1

Easy to Use:

  • Suitable for refrigerants R410A, R32 ECT that any with 1/4" & 5/16" SAE thread.
  • Great for vehicle or home air-conditioning with highly working performance.
  • High working pressure provides you with safety and convenience to test or recharge many HVAC system.

D. Romines
Reviewed in the United States on February 28, 2025
CAUTION!!!! The charge yellow hose is 1/4-in fittings on both ends which is useless if you're replacing 5/16 hose set on 5/16 gauge set while the high side and low side lines are 5/16 on one end and quarter on the other which is fine but it should be highlighted more that the charge line is a 1/4 inch on both ends. The ad that I read indicated they were 5/16 all hoses, and it may have been updated about the charge hose being 1/4 inch on both ends but not on the version that I saw. Also, like the other comments have indicated the seals are crap, nylon or plastic which makes them useless. Good luck on trying to get a seal, plan on replacing seals.
Aytton
Reviewed in the United States on January 9, 2025
Perhaps not the highest quality but gets the job done, I used to perform the vacuum and recharge the 410a refrigerant when needed on the minisplit ac units!
Shutterman
Reviewed in the United States on August 17, 2024
The hoses are okay but the gasket seals do not hold up to hand tightening for very long. As someone else mentioned, they are not made of rubber. They are either nylon or plastic because they are hard. Also, they have a tendency to flake-off, and the plastic flakes could enter a refrigeration line set and become a contaminate.I replaced the seals on the Schrader valve depressor with rubber ones and so far—after a couple of uses—the hoses and seals work fine.Bottom line: Surieen, or whatever company manufactures these hoses needs to quit using cheap plastic or nylon seals just to save a penny.* Update: I changed my rating from 2 stars to 3 since the company refunded my money on this hose set. I’m glad they did since I had to order rubber gaskets and take the time to replace their plastic ones.Hopefully, Surieen will change the design to include rubber gaskets for all future purchasers.
Customer
Reviewed in the United States on May 16, 2024
Poor quality
Hatem Ammar
Reviewed in Canada on March 30, 2024
The media could not be loaded.
ron kansas
Reviewed in the United States on November 27, 2024
I used this to replace old hoses.They are good enough but not great.
Pedro A. Rendon
Reviewed in the United States on October 23, 2024
They work extremely well...good quality, cannot complain.
Roberto
Reviewed in Italy on October 13, 2024
Perfetti
Roberson N.
Reviewed in Spain on September 22, 2023
Durou menos de um mês !
C Evans
Reviewed in the United States on April 29, 2023
The hoses are good and a Great value for the price. My only complaint is the seals that come in the fittings are a hard nylon type of seal. To get them to seat deep enough to depress a valve I had to use players to crank down on the fittings. This formed the seal and they worked a few times hand tightening. They original seals started to leak after a few uses. I got a pack of softer rubber seals. I replaced the originals and they work great when the new seals were installed.
lap137
Reviewed in the United Kingdom on August 14, 2021
Cheap rubbish
Red House 1
Reviewed in the United States on October 24, 2020
This set of hoses fit my old style gauge set and i can use then with new style fittings.