Your cart is empty.
Your cart is empty.Product Description
5V 12V 24V 150W High-Power PWM DC Motor Speed Controller Signal Generator Driver Module Speed Regulator
Description:
ZK-MG is a High-power PWM DC motor governor.It can adjusts the motor speed by adjusting the duty cycle of the output signal.
It can also adjust the output frequency to match the frequency of the output signal to the motor frequency, allowing the motor to work more stably.
Features:
Support ON/OFF output
Soft start function
Support set duty cycle
Support set frequency
Adjustable digital encoder
Instrument case
Support reverse connection protection
Support parameter memory function
Parameter Set Mode:
- Short press potentiometer: Select the parameter you want to set including Lower Limit Value of duty cycle, Upper Limit Value and Output Frequency, which could be switched by yourself.
*The lower limit of the duty cycle is displayed as "L" + two digits; The upper limit of the duty cycle is displayed as "H" + two digits or "100"; And the operating frequency is displayed as "F" + two digits.
- Long press potentiometer: Save parameter and quit setting mode to normal display mode.
- Rotate potentiometer clockwise: Increase the setting value.
- Rotate potentiometer counterclockwise:Decrease the setting value.
- STOP pads inside:It is used to connect to an external switch button to turn ON/OFF output if user need control output by another button or controller.
Note:
The module is a PMW driver, which controls the controlled device by changing the frequency and duty cycle of the output signal. It is not a voltage converter, it has no function to change the output voltage.
Adjustable digital encoder
The digital rotary encoder adopts the principle of digital pulse and output as the same as it rotates.
It will output the same value when it is turned back next time.
The digital encoder knob adjusts the motor speed, which has higher precision and better consistency than ordinary potentiometers.
Good repeatability, high precision, can be quickly adjusted to the value you want
3 Bit Digital Tube Display
Displays motor adjustment duty cycle, the upper and lower limits of the duty cycle and the frequency
In the default state, the duty cycle is displayed
5135 Instrument Shell
With standard 5135 instrument shell, with buckles on both sides
It is very convenient for you to install
Potentiometer introduction
1>.Long press means need keep press for more than 3second.
2>.Default display duty cycle.
3>.Normal display mode:
3.1>.Short press potentiometer:Turn ON/OFF output signal.
3.2>.Long press potentiometer:Enter parameter set mode.
3.3>.Rotate potentiometer clockwise:Increase duty cycle value.
3.4>.Rotate potentiometer counterclockwise:Decrease duty cycle value.
Use Steps:
1>.Connect right work voltage(Note:don’t connect load before set parameters）
2>.Short press potentiometer to turn OFF output
3>.Long press potentiometer enter into parameter set mode
4>.Short press potentiometer to select set parameters
5>.Rotate potentiometer to set parameter value
6>.Set another two parameters as step3 and step4
7>.Long press potentiometer to save parameters and quit set mode to normal display mode
8>.Connect load as wiring diagram
9>.Short press potentiometer to turn ON output
Application:
Drive motor
Light brightness control
Speed control
Signal generator
Florian
Reviewed in Germany on May 14, 2024
Hat bei 146W den geist auf gegeben! Leider stimmt die angabe 150W nicht ganz
Placeholder
Reviewed in the United States on March 23, 2024
it works If this thing lasts it will be a great. A nice red digital display for a eight dollars! Tested it out for a while and it seems to work fine. Install was a little difficult because it is made for a thin panel , the flange is so tiny that you have to cut your hole perfectly if you wanted to look good, and the wires come out the bottom making it difficult to slide in the panel hole, but still it is an amazing value.I would advise anyone using this product to tape the back panel on because it falls off when you pull the monitor out of the panel to which is mounted.so far a great value for the dollar. Product works exactly as advertised and as if that is not enough the Customer service via email is prompt and in good English!
Chris woods
Reviewed in the United States on December 30, 2024
I bought this to make a heater for my canam x3 side by side. Works great and I can control speed of fan easy. Only draw back is when you push to shut off it still stays lit up. I had to put a power of switch to keep from draining battery.
Daniel N
Reviewed in the United States on October 29, 2024
I only hope it will last a good while. The only thing i disliked was the pcb mounted screw terminal , well the position of it made it harder to use . If i had time i would desoldered it and solder new wire leads to the board and drill a hole through the back cover for the wire leads . Maybe next time on another project if i need another ill probably do just that. I also dont like that when it receives power its already in the 'on' state . You either have to push the button to power it off or turn it all the way down to 000 after each use so its off when it recieves power .
يوسف طلميس
Reviewed in Saudi Arabia on March 14, 2023
لم يشتغل معاي ويوجد تلامس كهرباء داخلي وغير صالح تماما والمنتج لا تستطيع ارجاعه
Mani
Reviewed in Germany on February 13, 2023
Der Artikel wurde beschädigt geliefert!
ch.locksmith
Reviewed in Germany on September 9, 2022
Der Drehzahlregler arbeitet bei mir einwandfrei. Die Einstellung mittels Drehknopf mit Rasterung geht präziese. Ich steuere damit einen Moror mit 12Volt und ca.35 Watt.
Customer
Reviewed in the United States on April 19, 2022
I had the product connected correctly. It worked for perhaps a total of 5 minutes run time staggered in three separate 2 minute runs. On the third run it started smoking. Input 12VDC driving small low amperage brushed motor for a stir plate. Didn't return it nor ask for money back. Just bought a different PWM from Amazon at roughly the same cost. No issues with new PWM with 2 dozen plus run times pushing an hour of total use. I notice the new PWM I purchased has beefy heat syncs. No led display but who cares it works. I do not feel it is appropriate to list the brand name of the working unit but you have been warned. This is only the 2nd negative review I have written over many years and many purchases. 1st negative review was over a shipping address change that was clearly done post ordering so I'm not a person to write negative product reviews so heed my words. As most know products do not always meet stated specs but I let those slide. Could I have just received a one off defective unit? Perhaps but judging from what I know about PWM's I not confident otherwise I would have asked for a replacement rather than simply moving on. Personally I wish all negative reviews of any product would also state how often that review writer posts negative reviews. I feel that is important in weighing the veracity of the comment. Perhaps Amazon could attach such a number or at least give the writer the ability to select the number vs the percentage of purchases. I suspect a less than glorious post written by a non complaining type carries more weight than the contrary.
atembedded
Reviewed in the United States on September 29, 2020
The media could not be loaded.
Deep
Reviewed in the United States on September 23, 2019
The media could not be loaded.
Recommended Products