Your cart is empty.
Your cart is empty.The Performance Tool W141 2-Jaw Gear Puller is a high-strength tool designed for exceptional durability and long-lasting performance. Constructed from heat-treated alloy steel, this gear puller delivers powerful pulling force to remove gears, pulleys, and flywheels with ease. Its drop forged construction and 2-jaw design ensures maximum grip and minimal slippage. The chrome-plated finish adds an extra layer of protection against corrosion and wear, ensuring that your gear puller stays looking and performing like new for years to come. Measuring 5 inches in spread, this gear puller is the ideal size for a wide range of automotive and mechanical applications. Whether you're a professional mechanic or a DIY enthusiast, the Performance Tool W141 2-Jaw Gear Puller is a must-have tool for any workshop or garage.
katy
Reviewed in the United States on January 15, 2025
The arm of my rear windshield wiper broke from the car wash. Well it wouldn't come off for me to replace the arm. Sprayed a little WD40 and using this tool it popped right off!
Wingnut
Reviewed in the United States on June 3, 2024
Probably works, but it's cheaply made and not durable.
Brian G
Reviewed in the United States on March 2, 2024
I used this to try and pull Bicycle cranks off of a bicycle... This is not the intended purpose of this tool.It was under advisement from a BikeBerry representative though trying to help me out.I can see however how this product while it may be effective in loose gear pulling, certainly has a way to go when it comes to the quality versus the cost... The metal is very soft, and I can't imagine it being used for it's original intended purpose for very long.Overall disappointing, and while i was using it for a extended use case, it failed spectacularly in very little effort.The Crank shaft likely can output as much as 8X the amount of force required to break the lever arms in this tool.
JD Smyth
Reviewed in the United States on October 29, 2024
This puller worked great for what I needed it to do when repairing my lawn care equipment. I can see it's going to be great for other small hobby and future small engine repair. I can see it isn't designed nor built for large mechanical uses.
R..Hawaii
Reviewed in the United States on September 7, 2023
I used this puller to remove the flywheel on my lawn mower. It did not do the job. The thin material used was bent and not able to remove the flywheel. I returned for a refund and purchased one that was twice the price. That did the job.
Kyle
Reviewed in Canada on February 15, 2023
The main screw is just tapped through sheet metal that is way too thin. The threads skip at the slightest application of force. Absolutely useless, this product shouldn’t exist. You’re better off attempting to pull whatever you’re pulling with your bare hands.
Daoudi
Reviewed in Canada on December 2, 2023
Je vous déconseille fortement cette article n'es pas aussi solide ,et se commentaire je ne le supprimé pas
ebmudder
Reviewed in the United States on October 3, 2023
I was attempting to remove a windshield wiper from the motor spindle. The device fit over the flange of the wiper assembly and had good contact in the gap between the wiper and the motor spindle, and the jaws were parallel to each other. Centering the pin on the spindle I started to turn using the provided handle. After 3-4 complete turns, the jaws bent outwards (putting the jaw faces at an angle) and the device slipped off the wiper. The jaws are now permanently bent. I didn't "over torque" the device and just used hand strength. I ended up using a pry bar to remove the wiper from the spindle, with minimal effort.
Collins
Reviewed in the United States on July 31, 2021
Don't expect to pull anything over a few inches with this. The finish has held up really well for the amount of abuse it's taken, but the long flats that sit behind the gear have bent over time, and it tends to slip off of whatever you're pulling unless you hold the flats together. Much better than a screwdriver or a hammer, but not an end all be all.
Keith D.
Reviewed in Canada on November 28, 2018
This didn’t do the job. Bent the jaws and handle. Might work ok on lighter work
I. Hunter
Reviewed in the United States on September 15, 2014
This is a small, light-weight, low-torque puller. I wanted it for limited-access applications where a more normal puller will not fit. The only down-side: "low-torque" puller. If you have a pulley which is really "on there," this puller will bend, break, fail.Kind of like what they sometimes sell as a battery terminal puller.Not a general-use puller.
Recommended Products
$16.49
$ 8 .99 $8.99