Your cart is empty.
Your cart is empty. About HICTOP PEI Sheet PEI Spring Steel 235x235 and Magnetic Build Plate with Adhesive PEI Bed for Flashforge Adventurer 5M/5M Pro,Ender-3 Pro/Neo,Ender-3 V2/Neo,Ender-3/Neo 3D Printers
Size: 235*235mm（9.25*9.25inch）
Package included: 1 x Steel platform with PEI flexible surface
1 x Magnetic bottom sheet with Adhesive
ADM
Reviewed in the United States on February 10, 2025
Super easy to install and use. Works great with my Ender 3 Max Pro Neo printer.
MG
Reviewed in the United States on January 26, 2025
Works great. My old school JGAraoura printer was plagued with adhesion issues and it would often take multiple attempts to get the first layer to stick. Zero issues with this plate. First print went perfect right out of the box.
Ronan
Reviewed in the United States on November 26, 2024
These are good plates and have had no problems with 3d parts not sticking. Only rarely have I had to add a brim on some parts.
Andrew J Cyvas
Reviewed in the United States on November 22, 2024
I have tired multiple bed temperatures, cleaning the plate with alcohol, detergent, and degreaser. I have tried printing with rafts and no matter what the raft ends peeling up and the print fails. So far I have had 0/6 successful prints with this plate and it's always because the print comes off the plate before it's finished. So far it all been failed PLA prints which should be the easiest. I would give it one star but it is sturdy and fits my printer bed perfectly. The adhesion problem makes it a complete waste of money for me however.
choninos
Reviewed in Mexico on June 24, 2023
La calidad de esta lámina es increíble, mejora muchísimo la adhesión de la primera capa. La compré cuando la original de mi Ender se rompió al desprender una pieza (la negra, no sé de qué material es), con esta estoy seguro de que no pasará lo mismo porque en cuanto la cama se enfría las piezas se despegan por arte de magia, ni siquiera tengo que flexionar la lámina. Tiene PEI por ambos lados así que sé que me va a durar muchísimo. Fue una gran compra
Flat
Reviewed in Germany on February 24, 2023
Ich habe schon diverse Stahl Kunststoff etc. Druckbettplatten ausprobiert. Das hier ist mit Abstand bisher das Beste sowohl bei Haftung als auch Wärme Stabilität und super robust. Während die Platte geheizt wird hält bisher jedes Filament. Nachdem die Platte abgekühlt ist das "Projekt" einfach abnehmen. Absolute Kaufempfehlung, sollte meine aktuelle Drucklatte Iirgendwann (!?!) mal durch sein, werde ich immer wider auf diese zurück kommen!
Grim
Reviewed in the United States on April 19, 2023
I was using the bed that came with my ender 3 v2 and thought it was pretty good. Well I was having trouble with abs adhesion so I decided to level the the bed closer to the nozzle. Big mistake. It adhered to the texture of the bed to the point I couldn't get it off. So I decided that I would use acetone to clean the bed. This was the nail in the coffin. It delaminate the top layer of the original bed. So I started looking through Amazon for a new bed. This one had great reviews so I decided to try it. Man printing has never been easier. My old bed had to be leveled every few prints. This one hasn't had to be leveled since I first installed it and have 20+ prints including one 25 hour print and counting. Abs does well and pla/ tpu is a breeze. No issues with adhesion and once the bed cools, the parts can almost be blown off. The only issue is that if you have a power outage and the bed cools, you will have to restart the print. Best settings for pla for me are 60°C bed temp and 210°C nozzle temp and you can run 90 mm/s. If you don't want strings (I usually just run a lighter over the print to remove so nbd for me but.. ) I recommend 70 mm/s or slower. I have an ender 3 v2 so keep that in mind for those settings. But for sure worth a buy haven't had the chance to use the flat side. 100% worth the money.
Andrea B.
Reviewed in Italy on September 20, 2022
Grazie a questo piatto PEI ho risolto tutti i problemi di adesione con il PETG e ora le mie stampe sono perfette. Nelle istruzioni ocnsigliano un riscaldamento a 90° per il PETG ma nel mio caso funziona bene a 80°, sicuramente dipende anche dal materiale usato. E' stata una svolta perchè con il piatto originale della Artillery Genius non c'era modo di far aderire bene il PETG, ora va come un treno. Estremamente soddisfatto.
Jess in PA
Reviewed in the United States on August 19, 2022
This was a game changer for me. PLA prints wuld have perfect first layer adhesion then pop right off once done and cooled. For the price it is at, it is amazing. However I did just purchase this about 2 1/2 months ago and while I have been printing fairly regularly, I just started to notice the PEI coating beginning to peel up where the first layers would often be. So I lost my print adhesion in this area. I have flipped it over and am using the glossy side with a bit of glue stick - but I will have to order another one. If the new one goes anywhere near as quickly, I will have to bite the bullet and buy an actual powder coated one, not just one with a thin layer of the textured material stuck on top like this one is. Again, for the price it is great. If you do not feel like dropping $100 right away this is a great option.
DeltaDracon
Reviewed in Italy on June 14, 2022
Articolo arrivato palesemente aperto e usatoBase magnetica distrutta.Base in PEI senza foglio di protezione e senza PEI (rivestimento letteralmente assente, un semplice foglio di acciaio), coperta di graffi e righe profonde.Reso immediato.Peccato perché sembrava ottima la possibilitá di avere sia il letto liscio che quello con la texture senza dover comprare due diverse piastre.
Alex Hauser
Reviewed in Germany on October 14, 2022
Spitzenqualität mit super Eigenschaften.
Rick Beebe
Reviewed in the United States on January 12, 2022
I've been have problems with getting my PLA prints off the print bed. I tried painter's tape which worked but left a little ridge at the seam. In this case I was trying to print something where the show face was down. Someone recommended this PEI bed. My printer has a magnetic steel platform so I didn't need the sheet magnet that came with this but it looks to be the perfect size and cut if I had needed it. And it's peel and stick to attach it to the printer.The first time I used this plate I was amazed. The print stayed put during printing but popped right off the plate when it was done. In addition, it left a nice pebbly surface finish which was PERFECT for my current application. I've printed six things in the past week and all of them stayed in place while printing and came right off when done. I love it.All that was with PLA. I have some TPU that I will try later. That actually stuck to my old bed so hard that the surface peeled off with the print. Painters tape was a necessity! I'll add an update when I try it.
EdGoldy
Reviewed in the United States on January 19, 2021
This arrived quickly, well packaged, and in good condition; Included in the package was a free nozzle - a nice little suprise! I've read a lot about PEI build surfaces in the 3D Printer online Groups of which I'm a member so I decided to make the leap. This build surface is 0.5mm thin. I took it out of the box, washed it with hot soapy water, rinsed, air-dried, and put it on the printer. My printer (Creality Ender 3 Pro) has a magnetic sub-surface from the factory so I did not have to install the one that came with this HICTOP PEI build plate. Because it's this is thinner than my previous surface, it required me to re-level the bed.The print side is the textured side which has a surface similar to about a 120-grit sandpaper. The underside (the side with the HICTOP logo) did have a few disolored spots (see picture) but since this side goes down, these do not adversely impact plate performance. Speaking of adhesion - it's phenominal!!! Tall, thin objects and tiny objects with only a little build plate contact is where adhesion is critical and this bed handled them flawlessly. To give you an idea of its adhesion, I ALWAYS peel off the purge line at the start of a print; not on this surface though - while the bed is heated to 60C, the purge line is stuck there so well I can't peel it off! Same goes for the printed part - it does not move when the bed is at temp. I saw zero elephant foot, zero warping/lifting, everything I've printed stayed flat to the surface and stuck there like it was nailed. But, like magic, when the bed cools to room temp, you just pick the part up like someone just walked by and placed it there; no popping or velcro-sound, no prying or pushing, just pick it up. It really is awesome.The platform provides your print with a bottom-layer surface comparable to the flexible magnetic beds.This thing is fantastic and it will be my only build plate going forward. Highly recommend!Only con is that there feels like a very slight burr on the edge so use some caution when handling.
Recommended Products
