Your cart is empty.
Your cart is empty.NEIKO introduces the 03972A Socket Tray with Magnets that can store up to 26 of your 3/8-inch drive sockets. Give yourself the neatness and organization your garage needs. We all know you’re going to lose the 10mm socket so have this magnetic socket tray handy to prevent losing your 10mm sockets. This magnetic socket holder and tool organizer is engineered with a strong ferrite magnet base that securely holds your sockets in place. These socket carriers give you the ability to carry your sockets in your tool bag without being all over the place. Know that your sockets will only leave this socket tray when you need it for a job and never on accident with the strong ferrous magnet base. Magnet strong enough to hold your sockets upside down under your car when working under your car. Vertical socket holder mountable to place on work surfaces or on the side of your tool box. Can also work in your drawer of your toolbox as a drawer organizer and with the easy-to-read identification numbers in high visibility you can find you desired socket fast. Hold 13 deep sockets and 13 shallow sockets in the following sizes: 1/4", 5/16”, 3/8”, 7/16”, 1/2”, 9/16”, 5/8”, 11/16”, 3/4”, 13/16”, 7/8”, 15/16”, 1”.
john
Reviewed in the United States on February 9, 2025
Great product. Fast shipping!
loic
Reviewed in Mexico on February 26, 2025
bien
BC
Reviewed in the United States on February 25, 2025
They work as they should.
Hugo Mtz
Reviewed in Mexico on January 28, 2025
Excelente, puedes tener todo organizado y olvídate de estar buscando lo que necesitas en una bolsa.
Mik
Reviewed in Brazil on September 3, 2024
Material de primeira qualidade, muito bem acabado, suporta soquetes até onde cheguei 27mm sem desprender. Pode ser utilizado na vertical, já que possui furação para fixação. E por último, é muito bonito de destaca entre as ferramentas.
The Otter
Reviewed in the United States on September 26, 2024
Needed some metric deep impact sockets. Was cheaper to buy a whole set than just three I needed, but came without case. The Neiko holds all 14 with space for some oddball sizes no one uses (20, 23 25-27). No problem with clearance for the thicker walled impacts.Very impressed with the magnet. Sockets held securely, but easy to remove. Deep sockets are heavier, impacts heavier still. With the entire set loaded, I can turn upside-down and none fall out. Holder attache to steel panels tightly - may be a little hard to remove.
Bill
Reviewed in the United States on December 3, 2024
This has marking for all the sockets, shallow and deep. The magnet holds the sockets in OK, none fell out during a gentle shaking test. The holder sticks and stays to the bottom of my toolbox lid without losing anything.
#TeamMelone
Reviewed in the United States on December 11, 2024
Very convenient having socket size options on the spot - especially under a vehicle. I’ve had these for a couple years and just ordered more. The grips don’t come off and the spring holders hold the sockets securely. These have been dropped and kicked around - very durable. Recommend.
Miguel Vargas
Reviewed in Mexico on October 4, 2023
Muy buen producto para tener esas puntas organizadas,lo recomiendo
Philippe
Reviewed in Canada on October 23, 2023
Can’t beat the quality for the price. It exceeded my expectations. I can carry a loaded rail without dropping anything. The only recommendation I have to anyone is to spray a little silicone to lube the rail for easy sliding. Very happy with purchase
Christian Acuna
Reviewed in the United States on December 15, 2022
Super convenient, they hold all my sockets. Only getting 4 stars because the cutouts for the sockets aren’t exact size so smaller sizes look kind of silly in it. But the magnet is strong, it doesn’t move unless you really pry it up, and it holds the sockets in place well.
Hunter Clarke
Reviewed in the United States on August 4, 2021
These are so far superior to the steel spring-clip socket rails I had been using it isn't even funny. I tested the 1/2" rail with some big stuff and I couldn't shake off anything deep or shallow up to about 1". Beyond that it gets a little iffy if you're carrying them around, but I don't know who's trying to carry around sockets that big on a rail anyway.I have seen numerous people mention the plastic caps on these and the other similar rails sold under different brands. I found that a 3/4" 8-32 machine screw and nut can be installed in the slot on either end to prevent the sockets sliding off. Then I stuck a 5/32" automotive vacuum cap over the screw to make it a nice rubber bumper, and tossed the original caps.These rails are about 17" long and that's too long for a 16" tool bag. So, since my 1/4 and 3/8 drive sockets don't need all that length, I cut them down and drilled a new hole for the screw on the cut end.Another nice thing about these is you can swap clips between the rails since they're all the same size. So I swapped a 1/4 clip and a 1/2 clip onto the rail with my 3/8 sockets and put both sizes of drive adapter on them. Now if I need to stick any of those sockets on a different size drive I have the adapter right there. Of course I did the same for the other rails too.Overall couldn't be happier. I'm definitely buying more for my impacts and deep wells. They're long enough to cut in half and use as mini rails for specialty sets like hex and Torx. Lots of possibilities. The only unfortunate thing is the Neiko only comes as a set, so I'll have to either mix brands or buy extra clips, but since these are a few bucks cheaper than the alternate brands it's probably not that big a deal.
Jack
Reviewed in the United States on January 13, 2020
I have had similar items from years past made by Craftsman. As my tool collection expanded and my eyesight dimmed over the years, it has become increasingly difficult to keep sockets organized and to readily select just the one I need. If you are like me, over time, certain sockets go AWOL, which is frustrating and a waste of time trying to pick through a jumble only to find what you are seeking isn't there, even though I have a socket drawer plate type organizer.I recently replenished my sockets with a fresh order of complete sets of laser etched 1/2, 3/8, and 1/4 standard and metric, 6 pt and 12 pt, and deep sockets. So I am also now using these rail type holders to keep everything organized and in its place. It has taken quite a few rails to hold the complete collection, which now has many duplicates. But the extra expense and convenience is worth it as I can either put the rails into drawers or attach them to the sides of my tool chests with magnets with hooks.I add a piece of tape to the handles to distinguish a metric rail from a standard English rail. It was a major job to sort and organize the jumble but once done, finding the right socket mounted on these rails is both quick and a pleasure.However, that being said, I do have an issue with the fact that one cannot buy (on Amazon) the individual rails, additional clips, or the colored plastic tool handles. This is the only reason for my rating of "fair," instead of excellent.As listed and supplied on Amazon, one is stuck with the 17 clips supplied per rail, and if you have more sockets than this, you are either SOL with Neiko, or you will end up buying additional sets just to complete a rail or two. In other words, I like the rails. They are functional, seem to be well plated, but the marketing aspect as dictated by Neiko is not consumer friendly. I would have preferred to order sets of three rails by socket size and to have additional clips available as a separate purchase as well as to have the polyvinyl handles available and easily distinguishable as to metric vs standard English dimensions. One can purchase on Amazon sets of 20 3/8" clips, and they do work on these rails, but having done so, I find that those clips while they will work are not as smooth functioning as the supplied Neiko clips.
Recommended Products
