This hot end was the single best modification I have made to my printer. It has allowed me to print at higher speeds and achieve much higher quality prints. The installation is straightforward and the tuning with a sonic pad is relatively simple. I was worried about the increased weight on the carriage. But it seems to not be an issue. Even when printing at 130+ mm/s.If you are looking for a quality direct drive hot end to improve your prints, look no further. You will not be disappointed.

Upgraded my cr-10S with this and the quality of the prints have vastly improved. Very well made and clear instructions

I purchased the Micro Swiss NG to replace the stock hot end and extruder on a older Creality CR10S-S4. At the same time I also replaced the stock main board with a TH3D Studio EZBoard v2. The Micro Swiss is a gorgeous piece of kit that functions and prints extremely well. I've been able to double the print speed while maintaining very high quality prints. My only regret is not upgrading to the Micro Swiss sooner. So far its handled every filament I've thrown at it with ease... PLA, PLA+, PETG, ABS. Every print is high quality. The combination of the Micro Swiss with the EZBoard has my old CR10S-S4 printing better than new. I've had the printer for 7+ years and with this upgrade will likely get another 10. Well worth the cost. A very reasonable price to pay for very reliable and high quality printing. Love it!

The media could not be loaded.

The print head is excellent! However, 400 e-steps is a good place to start. On my Tronxy XY3, I had to set it to 600. I did this by using gcode since I did not have access to the firmware. Where I later learned it is available on Github.Customer service responded to my emails quickly and kindly even when I was getting frustrated on setup. I work with RPET and I was having what I thought was some odd purge issue. I threw my hands up and decided to hit print. The print was the best print I have seen yet. Take the time and make sure you do your printer maintenance.

After watching the Youtube video and downloading the instructions PDF from Microswiss, this was quite easy (for me, who is used to tinkering with stuff) to install on the Ender 3 V2. I also installed a dual-Z kit at the same time.I am using the heater block from a Dragonfly BMS so I can keep using my V6 hardened steel nozzles (and my upgraded thermistor); it just screws right onto the heat break, no problem. If you are upgrading from a stock Ender 3, I would be prepared to buy a new thermistor (they can get stuck, and are very easy to break). Microswiss also offers a high-temperature heater block that is compatible with this assembly if you need it, but apparently nobody makes a silicone sock that fits.Be prepared to print your benchies and temperature towers, etc. You might end up needing to change several settings in your slicer.So far:-I have been able to print ASA, ABS, TPU, Nylon, and PLA very successfully. I still need to dial in the Nylon better, but I have everything else pretty much there. I'm also assuming it's going to work very well with the PC, but haven't actually printed with that since the upgrade yet.-To reduce stringing, I found that setting the "Wipe while retracting" setting with 100% "Retract amount before wipe" setting in PrusaSlicer really helped quite a bit. Also, for the TPU I needed to set the extrusion multiplier to 0.9, which also really helped a lot.-If you aren't using the nozzle that MicroSwiss includes, make sure you are using one that's high quality. I think the nozzle I had was not quite 0.4mm, and it really caused problems with the TPU. Don't mix and match either. If you are using the Microswiss heater block the extruder comes with, use an MK8 nozzle unless you like to clean up messes.-I found that I needed to adjust the extruder tension screw out a little further than recommended. With the 2.75mm recommendation for TPU (and the incorrect nozzle size), I got the TPU wrapped around some of the gears, and had to do some disassembly (wasn't too bad, mostly just annoying). I corrected both issues, and actually was able to get some pretty decent quality TPU prints pretty easily (I had never worked with flexible filament before, so I was pretty happy). I accidentally left it on 2.75+mm for the next print, and it handled PLA like a champ as well.-If you are going to be printing filaments that benefit from a hot first layer (like Nylon or ASA), you might also consider swapping to a more powerful 4020 hotend fan (which is inexpensive and fits into the provided shroud with no modifications - just need to make sure you have the correct length screws, since the fan is twice as deep as the stock 4010) to help keep the filament from getting too soft in the heatbreak, mushrooming, and getting stuck. This could happen, for example, if your nozzle is too narrow/partially clogged, your heat management is not correct, etc. If you've ever had issues with heat creep, I think that you should assume that it's going to get worse with the tighter tolerances in this hotend. You can also print custom shrouds - there are a few on Thingiverse - that can accommodate different fans.-Make sure you read the instructions; there are some important tips. If you try to insert the filament the same way you would on the stock bowden drive extruder, it's not likely to be easy for you. However, if you insert it while rotating the filament gently back and forth and then let the extruder pull it through with the gears, then it's far easier to thread than the stock bowden drive. I've had no issues/frustration at all with any of the filaments I've tried since I installed this new extruder.What I would improve if I could:1. It would be nice to offer a version that ships with the upgraded heater block (and a sock that fits) and a hardened nozzle. For my use case, I print a lot with abrasives (glow-in-the-dark ABS, matte PLA), and spend a lot of time on the hotter end of what the "default" heater block/thermistor are really intended for. I don't throw away the softer brass nozzles that come with hot-ends, but I don't ever actually use them either.2. I would add a small knob to the extruder so that you can rotate it manually (when the stepper motor is off). The stock Ender 3 knob kind of fits, but isn't quite right. I'll probably try to print something out in the future.3. Include a mount for the BL-touch and CR Touch (yes, you can print them out but I think most people have already upgraded to a bed leveling probe long before they get around to upgrading to a direct drive, so it would be nice to include).4. Add a few extra drilled holes in the backing plate to make it easier to design mounts for accessories (like filament runout sensors).

I don't understand how this thing has any positive reviews, it is nothing but problems. It has a special heat break that screws into the heatblock and comes loose as it heats and cools. It's super hard to get it seated all the way in the extruder so it clogs all the time. I've had numerous failed prints due to non-extrusion from clogs and other random extruder mishaps. I ended up giving up on the Microswiss and bought a Bondtech.

Night and day difference in terms of print quality and reliable printing, compared to the stock hotend, particularly for PETG. It is a beautiful piece of engineering.Since their instructions are more Marlin based, here is my Klipper installation experience:* Installed on an Ender 3 Pro / Klipper setup. Installation was straightforward. BTW - I hated messing with Marlin, and I am a software engineer, but find working with Klipper so easy.* Performed "e-step" calibration. They suggest starting with 8 for rotation_distance, I ended up at 7.8.[extruder]rotation_distance: 7.8 #microswiss* Adjusted the XY offset for BLTouch[bltouch]x_offset: -40y_offset: -10* Performed hot end PID calibration - no problems. I think because the Microswiss shroud better directs the fan, the control loop seems tighter than before.PID_CALIBRATE HEATER=extruder TARGET=245 ...once done, save...SAVE_CONFIG* Changed slicer to 1mm retraction. Haven't tried retraction / stringing tests yet, but no problems with 1mm.* Adjusted Z offsetFirst print benchy came back *perfectly* in PETG. Using stock equipment in the Ender3 pro, PETG was hit or miss.Some observations:* They don't provide a bracket for the BL/CR Touch, so print your own before you tear down your current setup. It should probably be in PETG or ABS for sufficient strength and heat resistance, which is a catch-22 because that is the reason most people switch to an all metal hot end. I would prefer if they included a metal bracket.* Because they reuse many components (both fans, heater element, thermistor), it makes the process much easier, since you aren't rewiring the control board. That being said, be very careful with the thermistor, they are super easy to break.* You might find loading filament a bit difficult. It will operate differently from the stock Bowden setup. Start the extruder turning first, then feed the filament. The gears will grab the filament as they are moving. I have also heard it is helpful to cut the filament end at 45 degrees.Overall, the best upgrade I could imagine. My congratulations to Microswiss on an excellent product!

Micro Swiss NG™ Direct Drive Extruder is not cheap but when you consider that it does what it says it does and never lets you down it is worth every penny.There are many things that can go wrong with a 3d printer. Removing one of the major headaches, hotend troubles, is a big thing. I have tried various extruders but none was trouble-free.This is fit and forget. I have used mine for the most challenging filaments, PETG and TPU and the extruder pushed them through without any problems. No clogging and no jamming as long as you adjust the tension arm correctly. Micro Swiss customer support is always there and is very helpful. "So if this extruder is so good why did you contact customer support?" When I first bought this I was having problems feeding the filament into it. Through support, I found I was not letting the extruder do the work, all I had to do was straighten out the first few centimetres of the filament and push it through the Bowden tube until it touched the gears and then via the printer's control panel feed the filament through. Easy Peasy. I don't often give 5 stars so believe me when I say this machine deserves it.

Habe den MicroSwiss NG geholt um weiches TPU82A zu drucken. Man sollte sich bewusst sein das die Extruder Fördergeschwindigkeit für weiches TPU langsam sein sollte weil das Hotend sonst mit dem schmelzen nicht nachkommt. (evtl werde ich einen Volcano anpassen um zu schauen wie schnell ich dann drucken kann.)Zudem sollte die Kühlung etwas verbessert werden - 1 Lüfter reicht nicht, ich habe 3 gestapelt.Jetzt schafft der Drucker spielend TPU mit 35mm/s, bis jetzt ist es der beste Extruder Kopf den ich kenne.

A partir d'un certain moment, quand on imprime beaucoup sur l'Ender 3V2, on peut avoir envie de passer sur direct drive pour un certain nombre de raisons, qui sont la plupart du temps valables.Le souci majeur, c'est le poids de l'ensemble en direct drive, ce qui oblige certains utilisateurs a rajouter un second moteur Z. Micro Swiss a fait un système bien pensé, et au global très léger. Suffisamment pour qu'il n'y ai pas de différence au niveau de l'axe X, a gauche et a droite lors du déplacement du système. Donc pour moi on évite des dépenses qui ne sont pas nécessaires, et ceci dès le début.Il y a tout ce qu'il faut dans la boite ( support de ventilo, pièces la plupart du temps déjà assemblées ) il faudra néanmoins récupérer l’élément chauffant, et le capteur de température, les 3 rouleaux sur l'ancien assemblage. Je trouve que c'est une bonne idée dans le sens où on les possède déjà. Le moteur est bien fourni.Le manuel de montage est dispo sur leur site, mais globalement c'est rapide a monter, et il y a les E-steps ( 400, mais a affiner ), ainsi que les variables concernant l'emplacement du BL/CR Touch a modifier, il suffit de reprendre ceux d'origine. Modifier les paramètres concernant la rétraction sous Cura aussi. Affiner ses réglages avec des tours de températures, et de rétraction ( MS recommande 1mm ).Je pense que c'est le type de système a acquérir après pas mal de mois passé a jouer sur les réglages en Bowden, tester plusieurs firmware etcLa buse et l'ensemble de ce qui est fourni est d'excellente qualité... le système est fiable, et avec le recul que j'ai dessus, il est excellent.C'est un peu a mon sens l'upgrade ultime sur une base qui fonctionne très bien en Bowden, mais là on est vraiment un cran au dessus, niveau perfs/résultats etc