Your cart is empty.
Your cart is empty.The Makita 10 Gauge Nibbler (model JN3201) features a powerful 6.2 Amp motor for continuous operation in up to 10-gauge mild steel or 13-gauge stainless steel. A built-in thickness gauge means more convenience, and all ball and needle bearings promote longer tool life. The Makita JN3201 also features easy punch and die replacement for less downtime, and double insulation for longer tool life. The JN3201 is engineered for less noise (only 81 dB(A)) for continuous operation.Convenient chip disposal below cutting material to minimize damage to cutting surface
gregory robinson
Reviewed in the United States on July 12, 2024
The nibbler is 100v.
Engrx2
Reviewed in the United States on February 21, 2024
RECEIVED A REPLY FROM MAKITA CORPORATE - YOU CANNOT USE THE 100 V JAPANESE VERSION THEY ARE SELLING HERE IN THE USA (IT IS NOT AUTHORIZED) AND ANY 100 V JAPANESE VERSIONS USED IN THE USA ARE NOT WARRANTIED.Great price, but they are deceptively shipping the Japanese 100 V, 7.0 Amp version in the US. The version they claim to be shipping is the 120 V, 6.1 Amp version which is not the case. Running the 100 V version on 120 V (can be as high as 126 V) will shorten the life of the tool and may even burn it out and will probably void the warranty. Manual is also in Japanese and not English or International.
日高利行
Reviewed in Japan on May 2, 2023
非常に満足しています。1.6mmもあるのですが、やはり最初から3.2mmを買うべきだったとおもいました。2mmの鉄板を使う事がよくあるので、3.2mmが余裕があり楽です。ただ、切断面が意外に直線ではないので仕上げ処理が必要な所が、イマイチかなと思います。
Customer
Reviewed in Canada on December 6, 2023
exactly what i was looking for! cant wait to try it! thanks to the seller for having this on amazon!
Timmy Smith
Reviewed in the United States on December 28, 2023
Might be great for duct work but I used on a metal roof and it did not perform over the humps as I would prefer. I am a Makita Man but this could have been make better and it probably does make them better than this for metal for a roof. These just wasn’t the best for my particular job. They might be perfect for metal that’s flat.
Sue Villarreal
Reviewed in the United States on November 6, 2023
The Makita nibbler is a quality tool as expected from Makita. The nibbler will cut in straight flat lines with no problem on pro panel roofing, but crosscutting was difficult because of the steep peaks and valleys of the type of metal panels I was using perhaps the smaller Makita nibbler would have worked better to reach into the valleys. The 5star rating to the customer service when it came time to get a refund, it was Smooth, fast and trouble free. I would consider doing future business with this company.
Alex Sanchez
Reviewed in the United States on April 21, 2023
We tested the JN3201 with a steel sheet of 0.068in thick (gauge 14) and cuts through like a knife through butter. Easy to handle and not heavy at all. Just go slow with wrinkles. This nibbler is compatible with American electrical standards in terms of voltage and frequency so you can use it with no concerns. Definitively we are going to keep this bad boy and try his sibling JS3201 anytime soon. ありがとうございました。
The Mad Inventor
Reviewed in the United States on September 3, 2020
To my surprise, its easy to cut a straight line without a guide, assuming you have a mark to follow. I was amazed how fast this thing cuts. I own and operate a welding shop and this tool increases my abilities greatly for cutting curves as I hoped it would. But I'm amazed how fast and easy it is for cutting straight lines and I did not expect that, but I love it. Great build quality. Much better than my Milwakee sheers.This thing is also great for accurately trimming off just a little material. You need to make it 1/16th or 1/8th inch smaller? No problem. Clamp on guide and go. Job done quickly, easily and accurately.
カスタマー
Reviewed in Japan on May 24, 2020
電気工事士です。ひとりで大きな鋼鉄製の分電盤をつけることがあります。反発力が強いですが、40mmの穴さえ開ければ、ジグソーの様に使えます。切り粕が鋭いので、掃除して、手に刺さらないよう注意が必要です。
sks
Reviewed in Japan on October 28, 2020
取扱説明書コピー、ﾒｰｶｰ保証書無し。これが普通でしょうか？
Koods
Reviewed in the United States on September 27, 2019
I've used this on a variety of materials so far. 1/8 mild cold roll, 16ga 304 stainless, automotive sheetmetal(est. 22ga), and 1/8" 5052 aluminum. It zooms through them. Easy to use with a straightedge also. I much prefer this over using something like a circular saw or cutoff wheel. Much safer and easier. The only downside is that you can't cut a very tight radius like you can with a smaller nibbler.
Bill Hountz
Reviewed in the United States on December 14, 2019
This tool cuts 10ga. steel easily. It is a great tool. It handles real good.
カスタマー
Reviewed in Japan on August 21, 2018
三日月形にくり貫きます。 くり貫いたものを拾うのが大変。養生をしっかりしておかないと、あとで後悔します。厨房の作業で使用したら大変でした。
Recommended Products
