Your cart is empty.
Your cart is empty.Chamfers plug for easy starting. Use with your Snappy quick change chuck in your drill press. Tight fit - no glue needed. You can match wood grain to conceal screw or use contrasting wood for a decorative look. Sharp clean-cutting tool is hardened for long life. Made in USA by Snappy.
Al Richardson
Reviewed in the United States on September 25, 2024
I've used them only on red oak so far. Very sharp, accurate sizing with no burning like some plug cutters. Works very well on my small bench top drill press. Great product.
Bob B.
Reviewed in the United States on December 28, 2024
I looked at a lot of different options for plug cutters. Most were fairly cheap and had reviews that reflected the quality that goes with the lower priced stuff. I purchased the Make It Snappy Tools plug cutter set and have been very impressed so far. They are very sharp, high quality tools. Using cherry, they cut very clean plugs and the bits were easy to use. Just make sure you use a drill press and clamp down your work piece.
Picky Consumer
Reviewed in the United States on October 11, 2024
good quality, works perfectly
AIS508
Reviewed in the United States on August 2, 2023
I do not own a drill press and was not looking forward to creating 500+ plugs with clamp, drill, unclamp to cut 1 plug. I created a jig with some scrap oak flooring and was able to use a hand drill to create 300 in an hour. Drilled a 5/8" hole for 3/8" cutter. Cutter held up perfectly for he first 300 after that I noticed it was tearing the wood or smoking while cutting. I used my lawn mower blade sharpener a few strokes along each tooth and it was cutting like new again. Once I got the hang of moving the jig around I was making the best use of the board.
Jason Corbett
Reviewed in the United States on July 26, 2022
I bought these for the primary reason that they were a set of plug cutters made in the US. The set I purchased covered the sizes I needed and came well packed and in good shape. I have used these quite a few times now over the past several months on very hard material (bone) for making perfectly round inlays. They cut well and get the job done. I use them in a drill press at the recommended RPMs for the size of the plug and material and they do what I need. The slight taper that is cut during the process does make fit into corresponding holes easier. That slight chamfer really makes for a tight fit. Thanks for a quality product Make it Snappy!
George
Reviewed in the United States on September 29, 2021
Using these to create hardwood plugs in a deck. definitely want to get them spinning before you make contact with the wood as they will go for a walk quickly. The plugs fit nicely but the cutters do make a bit of a rough cut overall. Hoping they hold out and don't break but seem pretty sturdy
Ed De Jonge
Reviewed in Canada on March 7, 2021
The cutters were dull and had to sharpen to use
Andrew
Reviewed in Canada on March 14, 2021
Not very sharp. Plugs came out pretty rough.
Gerald Mac Neil
Reviewed in Canada on September 3, 2020
It was well worth the wait for delivery. Fantastic tool. 😎👍👷♂️
Michael
Reviewed in Canada on December 2, 2020
Wouldn’t recommend and had a cancer warning on packaging.
ENRIQUE H
Reviewed in Mexico on September 21, 2019
Pésima calidad! Una de las brocas se rompió la segunda vez que la usé... No las compres, es tirar tu dinero a la basura y correr riesgos a tu salud además
rkruz
Reviewed in the United States on July 3, 2018
For the price I thought these would be much better than the significantly less expensive alternatives. I used the 1/2 and 3/8 cutters. The 1/2 cutter burns the wood. In this case soft maple. Occasionally and most annoying is that the plug will break loose and get stuck in the cutter. on the 3/8 cutter I did not have this problem and their was no burning on the same wood. The plug itself has a good taper and fits snugly and permanently in a forster bit drilled hole when hammered home.
Steve
Reviewed in the United States on January 10, 2014
These performed well and produced tight fitting plugs. The only reason I didn't give them 5 stars is because if you go a little too far down when cutting them, there is a tendency for the plug to break off. You can easily avoid this by setting the stop on your drill press.
Recommended Products
