Your cart is empty.
Your cart is empty.
Our Wood Chipper Blades are designed for the Landworks or SuperHandy Mini Steel Wood Chipper. The blades have a dimension of 4.15"L (105.4mm)(or 4-5/32) x 1.33"W (33.7mm) (or 1-21/64) x 0.18"H (4.5mm) (or 3/16). Each blade weighs 0.22lbs / 3.6 ounces. These blades have a Center-to-Center (Outer Holes) length of 3.16" & a Center-to-Center (Inner to Outer Hole) length of 1.55", with an Inner bolt diameter of Ø8.7mm & Outer bolt edge is Ø12.3mm.
These Chipper blades are precision manufactured to be mounted with (3) bolts holding each blade into place (*Note: the bolts are not flat but slanted at 10.9 degrees). We chose a very strong & long-lasting CR12Mov Steel material for our blades, providing excellent longevity of use. Our blade edges sit at a 40 degree, for optimal chipping capability.
These Chipper blades are precision manufactured to be mounted with (3) bolts holding each blade into place (*Note: the bolts are not flat but slanted at 10.9 degrees). We chose a very strong & long-lasting CR12Mov Steel material for our blades, providing excellent longevity of use. Our blade edges sit at a 40 degree, for optimal chipping capability.
marc macpherson
Reviewed in the United States on February 18, 2025
It's the wrong one for the chipper it recommended it for the chipper is a 2 bolt hole
Bobbyo
Reviewed in the United States on December 12, 2024
The blades in the photo we used to chip 18 years of growth in half an acre. Endless hours and they're barely worn. The new ones I installed were a perfect fit. I had no idea they were still good until I took the machine apart. At that point I figured I'd just change them. I'll save the old ones for backup.
JJALT
Reviewed in the United States on July 15, 2023
Not too pricey, good edge on blades, terrible procedure for blade replacement.Get yourself a good chest high place to work from , like a sturdy work bench, and put chipper on it. Remove wheels and outer shell of chopper to get at blades. Some rust buster or good penetrating oil to loosen up bolts. A good set of Allen wrenches would be nice. Make sure to disconnect spark plug cable before starting procedure!
twalsh
Reviewed in the United States on June 16, 2023
The good is that these replacement blades fit perfectly on my Great Circle 7hp Mini Wood Chipper. The bad is that they dull extremely fast. After about an hour of chipping up Douglas Fir branches ( green and about one inch thick) the blades lost about half their effectiveness. In about two and a half hours the blades are completely dull. I assume the metal is softer than other blades and dulls quicker. I hope to find other blades that will fit and hold their sharpness longer than these blades.
Charmaine
Reviewed in the United States on May 21, 2023
We bought a chipper shredder in the fall. Hubby used it until the snow prevented him from doing more. This spring, he used the chipper for a couple days off very heavy use. Noticed the blades were getting dull.Ordered these new blades. He installed them in less than 20 minutes and he was back to chipping in no time.Would highly recommend for anyone who has the super handy chipper shredder.
Brian K. Dickson
Reviewed in the United States on October 13, 2023
These blade brought the Garderbeaut back to life chipping wood and exact fit. Very sharp.
Irene
Reviewed in the United States on January 3, 2023
Sharp blades. Last a long time. Pain to change blades on chipper
Dragonheart
Reviewed in the United States on April 5, 2023
Reading the reviews one reviewer stated when asked if these blade would fit the Dex Brush Master Chipper. Instead of a definite NO! the reply was they needed modification. To me an accepted modification would entail a slight enlargement in the hole size to accommodate a larger size screw.. As an Industrial Engineer I can tell you only one hole out of the three could be lined up, necessitating recutting and enlarging the other two holes into an oval, which if fool enough to try would leave a severely weakened and poorly secured blade, highly likely to fracture sending pieces of hardened metal out of the machine at high velocity. To my knowledge all the Brush Master Chippers use the same blade, so the answer to this question is these blades absolutory DO NOT FIT the DEX Brush Master Chippers.
Recommended Products
$115.61
$ 51 .99 $51.99
$179.99
$ 81 .99 $81.99