Your cart is empty.
Your cart is empty.Product Description
Steven Thomson
Reviewed in the United States on January 29, 2025
I tried to return this, but I guess you only get 30 days wasn’t able to use it because I watched some videos and did some measurements and it only drops the CV axle a quarter inch rather than an inch and you’re not able to use a skid plate unless you modify it Because it sticks down too far and if you don’t use a skid plate, it sticks down farther and gets caught if you’re driving for wheel, so I’m stuck with it couldn’t return it and not gonna use it
jose martinez
Reviewed in the United States on September 8, 2024
I installed this drop kit in less than 10 minutes22mm socket19mm wrench for old hardwareThen will need22mm socket and7/8 wrench to installThis kit cost only $20 and it’ll save you $$$ by putting less stress in front differential of Tacoma 4x4
nmathay
Reviewed in the United States on May 18, 2024
Shop installed this with my lift, no vibration with this kit!
Customer
Reviewed in the United States on February 18, 2024
Almost perfect it’s bolted on good and easy to install but the bolts where a little short for a 5th gen 4Runner they still work but they are a little short
Thanh
Reviewed in the United States on April 19, 2024
easy yo install
LUKE NGUYEN
Reviewed in the United States on September 26, 2023
It fit perfectly. I will recommend
Alli L.
Reviewed in Canada on July 31, 2022
A must if you plan on raising the front end.
Bilal hamid
Reviewed in Canada on May 3, 2022
I waited for this for almost a year and never showed up, ended up buying bolts and washers from my local hardware store instead, cheaper and works well
ldev
Reviewed in Canada on March 18, 2022
Fits my 2003 toyota 4runner.After install, not much of a difference in the axle angle (3inch lift) but better than having full stress on the lifted axle.
Ryan Jones
Reviewed in the United States on January 30, 2022
The installation was pretty easy, no real instructions, but it's pretty obvious though. However, while it came with two bolts that were longer to allow the skid plate to reach after the spacers were put in. But, it needs two more longer bolts for the back skid plate. It isn't a deal breaker, but it was kinda annoying to have to go get one. You also need two more spacers, or, 4 larger nuts to go over the bolts to make a spacer. I wish I had pictures, but didn't think about it until I was finished with the installation.
Customer
Reviewed in Canada on July 13, 2021
Love the attention to detail!
Darylrl
Reviewed in Canada on March 15, 2021
Just installed this kit.1. Main bolts that hold the diff up are marginally long enough. If I used the washer provided the threads would not protrude the nut! So the nylock bolt would be of no use unless you omit the washer.2. The smaller spacers provided to shim the skid plate down are of no use. They are approx 1/4” thick. You need a spacer that should be the same thickness as the large spacers.3. There were NO instructions in the kit. Not a problem for me but for some it may be an issue.4. You will no longer be able to use the jack point on the skid plate as the kit spaces it away and provides no shim or suggestion to fill the space. Instructions or a mention of this on the sale page would have been nice!.....so I am now unable to run my skid plate till I get shims/washers to take up the space.I do not recommend this kit, to anyone. If it was in its allowable return timeframe, it would be returned!
MyNardo
Reviewed in the United States on October 22, 2020
Good product, the package will come with diff drop spacers, skid plate spacers, long bolts and nuts. However it will need the following.You will need longer bolts and washers for the rear part of the differential skid plate. You can use the stock bolts but the skid plate will hit against the differential.You will also need longer bolts and washers for the back of the oil pan skid plate, because since adding the 1 inch spacer for the differential, it created a gap for the rear of the oil pan skid plate.I'll have to double check but I think the bolt threads for this is M8x1.25. What ever the stock bolts are, add either 1/2 to 1 inch of total length and add washers for spacing and get it at any hardware store.Update: I bought M8x1.25 x 40mm bolts for the rear oil pan skid plates and used a large nut as a spacer. The nut doesn't need to thread to the bolt. The rear of the diff skid plate i used M8x1.25 x 30mm plus washers.
Recommended Products