Your cart is empty.
Your cart is empty. LCD12864 Display Controller Adapter Board with Adapter and Cable for 3D Printer RAMPS 1.4 Reprap Mendel Prusa for Arduino
The intelligent controller includes an SD card reader, rotary encoders and a 20-character×4 line LCD display.
You can easily connect it to your RAMPS 1.4 board using "smart adapter" included.This panel connect your RAMPS 1.4, you do not need your computer, your SD card intelligent controller power supply.
All further operations, such as calibration, the axis movement can be done only with a rotary encoder intelligent controller. 3D design print without a computer, just use the G code design stored on the SD card.
Package Included:
1 x 12864 LCD with Control Panel for 3D Printer
1 x Connector
2 x Cable
Enrico Maria Oggioni
Reviewed in Italy on February 19, 2023
Nessun Commento Particolare
K. Bell
Reviewed in the United States on December 30, 2023
CURRENT REVIEW: 1/06/2024Quality control seems non-existent, this one the POT to adjust contrast DOES NOT WORK. It is also so bright that TEXT is washed out. HORRIBLE.Debating if I want to go through the hassle of packing it for return AGGRAVATING! After waiting for it to ship then getting a complete lemon.PREVIOUS REVIEW:Contrast not as high and sharp as previously purchased.WARNING!!(Accidentally placing a STEPPER DRIVER in upside down, will more than likely FRY EVERYTHING including this connected LCD).For this reason specifically, STEPPER DRIVERS should be designed with an alignment PEG/HOLE, making installing upside down impossible - this is a simple design change, not requiring fancy resistors or capacitators. FOR ALL MAIN BOARDS
TLMG
Reviewed in the United States on November 6, 2023
Was absolutely perfect on my Tevo tornado.
Ronald P.
Reviewed in the United States on October 20, 2023
the display works nice, a good addition to my ANET A8 printer, the only problem I found is the the pins are wrong backward had to reverse the pin locater around, with needle nose pliers carful not to damage the pins, went to all four corners little by little until it came off then reversed it. other wise would be 5 stars
Jsn
Reviewed in the United States on September 27, 2022
The unit looks and works well however a lot of frustration can be resolved with any documentation for the device.
M. Marek
Reviewed in the United States on June 7, 2022
I am alwys happy with HiLetGo delivery and product value.The original Smart Controller Board in my Tornado 3D print encoder failed.The Tornado has a MKS GenL V1.0 motherboard and at first the LCD would notlight up. Found that I did have to reverse the ribbon cables at the controller whichrequires sanding off the connector key. Once I did that everything fired right upand the printer is back online.Did not rate the Touch Screen category simply because this display is not touch screen
Michael Mallory
Reviewed in the United States on August 10, 2021
Works great on my MPCNC running a BTT SKR 1.4 Turbo
Niki Schering
Reviewed in the United States on January 25, 2021
If you read some forums about the original clones of the Discount Smart controller the said you have to flip the sockets over on the board. This is not true with this unit.. It works as delivered.Running with Marlin 2.07 I added this line to prevent display creep.add before the getting started line in Config.h// Display creep timing fix for RepRap Discount Full Graphics display#define ST7920_DELAY_1 DELAY_NS(0)#define ST7920_DELAY_2 DELAY_NS(400)#define ST7920_DELAY_3 DELAY_NS(0)
jesse
Reviewed in the United States on December 1, 2020
Just got it. Not sure how to wire it without a diagram yet. Not sure if it will work on an UNO and a CNC sheild
Recommended Products
$56.65
$ 25 .99 $25.99
$206.99
$ 83 .99 $83.99