Your cart is empty.
Your cart is empty. Description:
Universal SOIC, SOP8 (EZ) SO8 TO Dip 8 Adapter 150mil IC
Programmer (1.27mm Pitch) and all SOP8 narrow chips
Suitable For : ALL-11 Series, ALL-100GANG, LT-48 Series, Super PRO Series, TOP Series etc.
Support Chips: 24CXX, 93CXX, 25 Series and all SOP8 narrow chips
Package Included:
2 * SOP8 to DIP8 EZ Programmer Adapter Socket
LG
Reviewed in the United States on March 3, 2025
Work great, good quality and functionality, easy to install and remove chips, no issues at all thanks
Jaafar Alsalaet
Reviewed in the United States on July 15, 2023
the adapters look of good quality and perfectly clamp the chip, I used one of them to program PIC12F510 mcu without any problem.
unhappy
Reviewed in the United States on June 20, 2023
Lower quality than expected especially on injected plastic body. Will not last many uses as I needed.
Aaron Kelly
Reviewed in the United States on March 9, 2023
It works well. What else is there to say? I use it with my XGecu t56 programmer, and it works. Far more convenient than soldering the chip onto a carrier.
AB
Reviewed in the United States on February 10, 2023
Hello All,Out of the bag, these products appear to be well made... AND, you get two of these for the cost which is a great value! Today, I went to assemble my programming/debugger adapter board and noticed that this socket adapter did not fit easily into the DIP-8 PCB footprint. Measuring the pin spacing on the adapter board, I noticed that it was NOT the common 300 mil spacing found on DIP-8 sockets. The pin spacing was 287 mils. Fortunately, I was able to carefully force the pins into my programming adapter. It would be nice if the seller could list this specification on or near the product page.Best regards,AB
Captain Bill
Reviewed in the United States on December 13, 2023
I needed a good socket to clone a GMC 2007 Envoy Denali EEPROM 95040 chip (SOIC8) and this socket holds the chip very securely and the contacts are reliable. I duplicated 5 additional spares just for fun and this socket never missed a beat. BTW, before using these, I bought and tried the "clip on" IC clamps which are sold to clamp onto a SOIC8 that is mounted on the PC board. These clamps constantly let go, fall off, and the connections are electrically unreliable/noisy. I returned those and use these instead. It's a bit of work to swap out the chips but if you have the skills, this "ziff" holder is exactly what you need to copy/clone the EEPROM related to your car's VIN number for the Body Control Module. All good !! No towing to the dealer required anymore - not to mention saving about 500 bucks or more.
Bob
Reviewed in the United States on December 12, 2023
These are very inexpensive and should not be used in a serious engineering environment but for occasional hobby use you can get by. The biggest problem is the legs of the IC do not always line up correctly. I typically have to nudge the IC around a bit under the microscope before releasing the clamp.
Matthew Valancy
Reviewed in the United States on May 15, 2022
These are great and inexpensive but make sure you need the narrow type. I need wide for my attiny85v so had to place a 2nd order.
とまと
Reviewed in Japan on September 2, 2021
ちょっと、使いにくい。でも安いから。
カスタマー
Reviewed in Japan on August 11, 2021
問題なく使えました
サルマ茸
Reviewed in Japan on January 30, 2021
150mil専用であることに注意してください。（パッケージ部分が約5mm x4mm の縦長となります）挿入が若干渋めですので、ピンセットよりラジオペンチの方が作業しやすいかもしれません。クリップする際の感覚は素晴らしく、電極の接触についても安心できそうな形状です。prime対応ということで若干高めの価格価格になっていますが、配送が早いのでこの点については文句ありません。
雷鳴リーマン
Reviewed in Japan on September 3, 2017
3品同梱だったから、と云う訳では無いと思いますが、クッション材付き封筒による簡易包装のみではピン曲がりの発生は避けられないのかも。致命的なものでは無かったので修正は出来ました。
カスタマー
Reviewed in Japan on May 18, 2017
業務でEEPROMの書込みで使用しています。跳ね上げ式より使い易く、接触不良が少ない様です。新品ＩＣで、数百回以上は十分書けています。同じ様なＩＣ形状幅150milと２００milタイプが有りますので、SOP8 広い／狭いは要注意です。ピンセットが入りづらい事もありＩＣ上側の止め板は抜けますので、（自己責任）で外して使っています。この価格で入手出来るのは驚きです。プチプチ入りで郵送なので、多少の足の曲がりは仕方無いと思いますが、私の買ったものは、足がスポンジに刺さっていて問題有りませんでした。
Recommended Products
$105.99
$ 50 .99 $50.99
$80.99
$ 33 .99 $33.99