Your cart is empty.
Your cart is empty.HHIP Machinist's Bench Block Made from hardened and ground steel. A handy tool for holding work when driving pins, drilling, etc. The knurled side provides a good gripping surface. V-groove across the face accommodates round and odd shaped stock. Holes from 1/8 to 5/8" diameter. Block has a 3" diameter and is 1 1/2" tall.
Rockiesrider
Reviewed in the United States on June 26, 2024
Could be a little heavier but quality is there
Ron
Reviewed in the United States on June 17, 2023
Very nice bench block, works just as good as other higher priced blocks.
jorge beltran sanchez
Reviewed in Mexico on May 19, 2023
Esta un poco pequeño y delgado pero esta muy bien acabado
BritBrat
Reviewed in the United States on February 13, 2023
Just what you need when removing pins or the like, V groove is just what you need on occasions. Very helpful.
Keithtoo2003
Reviewed in the United States on February 24, 2022
The product is good as expected. The delivery was bad. I had this delivered to where my wife works so it won't be stolen off of our front porch. This was left outside all night long, and was not handed to a "resident" as stated in the delivery notes. Really disappointed.
Ian Mazursky
Reviewed in the United States on August 6, 2021
This is a nice machinists block. Not a Starrett but good enough for what im doing.It has a good weight to it and I would have no problem using it in my cheap arbor press.Its definitely worth picking up. The standard cheap arbor press plate are a joke and this block really helps keeps things flatter.
Customer
Reviewed in Canada on January 14, 2021
Well made basic bench block , good for driving out roll pins
J Osborne
Reviewed in the United States on December 7, 2020
I was contemplating buying the Starrett version of this but thought I'd give this a shot for the price and see how it was. Y'know, it's very nice and I don't see one single thing to complain about. Well machined and bored, holes on the groove are centered. The knurling is outstanding and all of the outer surfaces are great. Anvil thickness is 5/8" or a tad better. The bores aren't chamfered on top and I may to that just to break the edge a little. This may be a softer steel than what Starrett uses (haven't given it any good abuse yet) but I think for anything I do it'll suffice just fine. Great buy especially if you find it on sale here.
Wayne
Reviewed in Canada on January 26, 2019
Kinda Small but handy...hardened and nicely knurled. For the price it's hard to beat
Adam Yablonski
Reviewed in Canada on January 15, 2019
Block is nicely finished overall but the holes were not centered even remotely on the Vee Groove.
RTfact
Reviewed in the United States on June 30, 2017
I'm no machinist, so it made no sense to tie up serious money in a Starrett or other classic. This seems well crafted and is very handy for the bench.
Maria Dunki
Reviewed in Canada on December 17, 2017
It’s a present, so I can’t really rate it till the recipient of the gift comments.
Michael W. Oliver
Reviewed in the United States on October 20, 2017
Ok, it's no Starrett, but for as much as I use it, it works fine. The actual size is smaller than what the picture would lead you to believe, so keep that in mind. The knurling on mine was not diamond, as in the picture, but rather straight knurls. The knurling discrepancy is not a functional problem for me, but since it's not what I expected based on the product image, I'm noting it here so that *you* aren't surprised. All in all, it functions as I'd expect it to and I'm happy with the low cost.
Recommended Products
$41.38
$ 20 .99 $20.99
$40.11
$ 17 .99 $17.99