Your cart is empty.
Your cart is empty.Product Description
1X & 10X Oscilloscope Probe
Frequency Compensation
Before taking any measurements using a probe, first check the compensation of the probe and adjust it to match the channel inputs.Most oscilloscopes have a square wave reference signal available at a terminal on the front panel used to compensate the probe.Connect the probe to the signal source on your oscilloscope.Set the probe to 10x position.Adjust trimmer until seeing flat-top square wave on the display.
Voltage vs Frequency Rating Curve(RMS)
- CAT II
IEC measurement category ll is for measurements performed on circuits directly connected to low voltage installations. Examples are measurements on household appliances, portable tools and similar equipment.
- Equipment fully protected by DOUBLE INSULATTION or REINFORCEDINSULATION.
- Review this user manual carefully to avoid any personal injury or damage to this product and any product connected to it.To avoid potential hazards,use this product only as specified.
- The measurement category of a combination of a PROBE ASSEMBLY and an accessory (an auxiliary to the measurement ) is the lower of the measurement categories of the PROBEASSEMBLY and of the accessory.
- Follow the instructions to use the PROBE ASSEMBLY will impair or ruin its self-owned protection function.
Accessories and Features
Probe is provided with several accessories designed to make probing and measurement simpler.Please take a moment to familiarize yourself with these accessories and their uses.
- 1--Slide Switch: Use the slide switch to set probe attenuation.
- 2--Compensation Trimmer: For frequency compensation adjustment in 10x mode.
- 3--Ground Lead: Use the alligator clip to attach the probe to a ground reference.
- 4--Hook Tip: Retractable hook tip.
- 5--BNC Connector: Connect to the oscilloscope measuring channel.
- 6--Adjustment Tool: Use the adjustment tool for probe compensation adjustments.
- 7--BNC Adapter :Realize the mutual conversion of signal.
- 8--Locating Sleeve: Using locating sleeve could ensure the stability and reliability of the tip exposed to the test point.
- 9--Marker Rings: Attach the matched color rings onto the probe cable and shaft to identify different channels.
- 10--Ground Spring: Provides shorter grounding path for better signal integrity.
DT
Reviewed in the United States on December 16, 2024
I received 2 of these in a kit. One of them is out of adjustment. The adjustment procedure says to turn a screw using the supplied tool. Neither of my probes have visible screw slots for the pots.
William Mathers
Reviewed in the United States on March 23, 2023
Got a laptop Oscilloscope and found one of the probes to be faulty. This was a good replacement at a good price. Ta Da
Benjamin
Reviewed in the United States on February 2, 2023
Not as described. Not 2pcs as listed. Single probe delivered in a resealable bag? Probe appears to be of lower quality than other Hantek probes/products.
Arthur F. Lange
Reviewed in the United States on March 15, 2022
Two channels and a variety of triggers. Nice for transient capture.It works well for me.
Suresh Nair
Reviewed in India on January 13, 2022
The Oscilloscope probes are in good condition and working properly.I recommend the product for buying.
F. Morgan
Reviewed in the United States on April 29, 2022
Good stuff
jlamp
Reviewed in the United States on September 19, 2021
great price ,works with my pico scope,would buy again.
The Quick Engicon Services
Reviewed in India on February 6, 2021
Very good product
D. L. Fuller
Reviewed in the United States on November 27, 2021
High quality, good price, quick delivery.
mamtora s.
Reviewed in India on October 26, 2019
Nice product. Sane as expected.
SHEKHAR M.
Reviewed in India on September 13, 2018
Its Good.
Customer
Reviewed in India on August 6, 2018
Good product. Working fine.
LU GUO
Reviewed in the United States on July 21, 2016
These are for my friend, and he said they works perfectly. I am happy to make this purchase！
Recommended Products
$9.58
$ 3 .99 $3.99