Your cart is empty.
Your cart is empty.Product Description
Alltooetools Engine Injector Removal Puller Kit
The tool is designed for 1.4, 1.6, 1.8, 2.0, 2.7 V6, 3.0 V6, 3.2 V6, 3.6 V6, & 4.2 V8 FSI TSI TFSI Gas engine injector remove, installation, and reseals.
This Injector puller set easy to pull injectors, help you to reseal and reinstall fuel injectors, saved you a lot of time.
Made of high-strength steel forged, precisely machined and heat treated, Make the tools has high hardness, strong toughness and is not easy to be damaged.
Includes Part1
1PC ball-type insertion adaptor
1PC 23 x 76mm large cup FSI puller
1PC 14 x 40mm small cup FSI puller
1PC 19 x 20mm two leg thin FSI puller
1PC 15 x 10mm threaded cup pulling adaptor
1PC 10 x 8mm threaded cup pulling adaptor
1PC slide hammer puller
1PC 9.5mm disconnect key
1PC Brush
Includes Part2
2PCS 12/13mm ID x 40mm L cylindrical adaptors
2PCS 27 x 4mm & 35 x 7mm tapered cone adaptors
3PCS 24mm knurled stepped adaptors
1PC 19mm OD x 12mm ID x 12mm L spacer bush
JHFullboost
Reviewed in the United States on August 3, 2024
I was doing a valve carbon cleaning on a 2015 vw tiguan 2.0 tsi. Had to get new seals for the injectors so I purchased this tool kit. Did a good job of getting the seals seated on the injectors.
Angel L Rolon
Reviewed in the United States on April 25, 2024
NA
Christopher
Reviewed in the United States on August 28, 2023
Use as intended by description
Ron P.
Reviewed in the United States on April 24, 2023
Kit is designed for what it states although you can use the taper and ring guides in this set for a 1.5L which buying this set is less expensive than the same parts alone specifically for ford
Daryl
Reviewed in the United States on September 18, 2022
I had to remove all direct injectors on a VW Touareg and the kit worked perfect. Only wish it had instructions because there’s pieces I don’t know what to do with. But it worked for what I needed to do.
Dean
Reviewed in the United States on November 12, 2022
I needed to remove and clean the fuel injectors on my 2008 Audi A6. I gave this tool a try and it worked great. The slide hammer remover is a little fiddly since you can't screw in the handle all the way or there won't be enough room to get it onto the injector. The remover worked and the seal installer worked. Worth it to save hassle trying to get direct injectors out with generic tools.
J.R.
Reviewed in the United States on December 28, 2020
The Subaru dealership quoted me $153 in labor to put the seals on. Never done this before. There is a video by the youtube channel "Humble Mechanic" that uses this exact kit.The video is titled "Replace injector seals on direct injection engines"Everything else in the kit is super extra and you just need the little cone. It is the exact diameter as the BRZ direct injectors. The smallest donut doesn't fit over the cone. So get it started with the knurled ends towards injector, move on to the medium one and slip it on. Flip the donut around and gently twist it in place to shrink the seal. Let it sit for a couple seconds.Saved myself over a $100 and definitely recommend it.I do recommend getting calipers and measuring the diameter of your injector tips if you get this for another motor. Can confirm it works for the GT86/FRS/BRZ though
Dan04mcs
Reviewed in the United States on December 28, 2020
2.0 2011 TiguanWhen doing the carbon valve cleaning more than likely some injectors will pull out of the head when pulling the intake.This tool made it very easy to change the seals on the injectors.No instructions, search for videos on how to use it.
Recommended Products