Shopping Cart

Your cart is empty.

Your cart is empty.

Dusk to Dawn Sensor for Outdoor Lighting 120-277V Photoelectric Switch Photocell Light Sensor Hardwired Post Eye Light Suitable

Free shipping on orders over $29.99

$14.99

$ 7 .99 $7.99

In Stock

About this item

  • Rated Voltage: 120-277VAC;Ambient Temp: -40℃~+70℃;Sensing distance: 3-8M; Load power:500W;Power Consumption: 2W
  • Automatic switch: Automatically control lighting based on environmental lighting level; The internal design has an automatic ambient light level detection circuit that can be automatically turned off during the day and turned on at night. In addition, a preset 3 to 10 second delay can avoid misoperation caused by spotlights or lightning at night
  • Outdoor design: Outdoor light fixtures and photoelectric switches are equipped with waterproof covers, with a protection level of IP65 for outdoor use. The dual protection sensor lens can avoid dirt and dust, and help the switch work better in harsh environments such as rain, wind, snow, etc.
  • Easy to install: The light controller can be used in conjunction with most hardwired outdoor lighting fixtures and bulbs, which require a mounting hole with a diameter of less than 0.6 inches. Disconnect the power supply, remove the junction box cover, place the Phototube optical switch in the tapping hole, and fix it with the lock nut.
  • Wide application range: suitable for automatic switching control of solar LED lights, street lights, courtyard lights, corridor lights, and other lighting fixtures (please remember that LEDs use DC power, other voltages are not applicable); can also be used as photoelectric switches for small rainproof street light controllers



Product Description

dusk to dawn sensor
light sensor

Specifications:

Rated Voltage: 120-277VAC

Rated Frequency: 50/60Hz

Rated Loadings: 500W Tungsten/850VA Ballast/5A E-Ballast

Power Consumption: 2W

Operate Level: 10~20Lx On/30-80Lx Off

Ambient Temp: -40℃~+70℃

Related Humidity: 99%

photo cells for outdoor light

How to connect:

一、The black wire is the ground (-) of the battery connector or power source, the load common or ground is not involved with this connection

二、The white wire is the positive (+) of the switch (the positive connection of the load goes to the positive of the battery together in parallel )

三、The red wire(the actual switched wire) is the ground (-) of the light, It switches the ground to the load.

photocell sensor

Connection method:

一、The WHITE wire AND the Positive Connection of the Load goes directly to the positive connection of the source or battery. Both wires. The load and the switch positive in parallel.

二、The BLACK wire from the switch goes directly to the negative or ground of the source or battery. Note: This will be the only ground or common connection to the source or battery.

三、The RED wire is the actual switched wire. It switches the ground or common connection of the load to the source or battery. The red wire of the switch connects to the load common or ground.

light sensor for outdoor lighting

Mark
Reviewed in the United States on January 22, 2025
These are perfect for my project
jeffrey m.
Reviewed in the United States on August 21, 2024
I had to lights that the sensors were no longer working on. These were great replacements in winning quickly. They function perfectly, and are responsive to quantity of light. Recommend!
bill gohl
Reviewed in the United States on March 14, 2024
None of THREE worked.. Bought one at Home Depot and it worked fine.. This was a total waste of HOURS of my time.. Should not even get one star..
Richard Langston
Reviewed in the United States on December 5, 2024
I liked the Sensor for Outdoor Lighting because it is possible to attached to any kind of light.
Johnny Tire
Reviewed in the United States on December 6, 2023
Too small for the hole that is in my outdoor light post. They look just fine.
Recommended Products

$13.85

$ 6 .99 $6.99

4.5
Select Option

$15.00

$ 6 .99 $6.99

4.7
Select Option