Your cart is empty.
Your cart is empty.Allgood Automation
Reviewed in the United States on February 18, 2025
Worked Well for a DIY Spot Welder controlling a Re-Wound Microwave Transformer.
Customer
Reviewed in Canada on January 13, 2025
Really really nice product works awesome
GPB-NJ
Reviewed in the United States on September 10, 2024
The unit worked well for about 30 days continuous operation and then failed completely. Just not a robust enough unit for continuous use.
Jacob Krogstad
Reviewed in the United States on May 8, 2024
I need a way to control the grid heater on a pickup that I swapped a cummins into. This works great for controlling how long the heater runs and I can adjust run time easily for different weather conditions. Directions were straight forward.
James Peterson
Reviewed in Canada on December 7, 2024
Use on an induction heater to anneal shell casings. Bought 2 incase I needed a backup...it is gathering dust in the back of our reloading room. I would say approximately 8000 rounds. Simple to use for an old guy like me.
Customer
Reviewed in the United States on November 8, 2024
As others have said the instructions leave a lot to be desired but I can at least share my experience with it.I have an el34 tube amp in may garage that puts out some serious wattage. It’s hooked up to an aiyima t8 Bluetooth/ preamp. When the aiyima shuts down it sends a decent spike to the amp and speakers making a loud speaker destroying pop. I have everything hooked up to a smart plug so everything shuts off at the same time. This isn’t a problem with solid state as much because solid state is on or off unless they have some crazy capacitance. Tube stuff doesn’t shut right down since the tubes are still hot and flowing whatever is left in the capacitors. What I needed was something that would delay the preamp shutdown until the tube amp is completely powered down.There are 9 modes on this thing. What are they? I have no clue the instructions are very poorly translated but you can kind of guess. I can really only speak for mode 8. Mode 8 starts a shutdown timer when voltage is lost at the signal input which is inside the timer box. I’m using a usb power supply for the trigger which would be considered a high signal. So I have it set to mode 8 at 20 seconds. When the usb looses power (connected to the same switch) the timer starts counting down and then opens the relay for the 12v (plugged into constant power) that sends power to the preamp. It works as it should.A few notes. The instructions say when it displays “out” that the relay is open. This is the opposite, the relay is closed when “out” is displayed. There are 2 options for relay status, CL and OP. I believe they mean close and open but I don’t know if they mean normally open or open after the trigger is there. You can change where the decimal point is for the timer by holding one of the buttons which makes it more confusing. There is also no plug for the trigger connections but I found something that worked you could also solder to the pins. I found that reading the instructions to the best of my ability and experimenting worked the best but
ian Cannibal
Reviewed in the United States on October 22, 2024
relay and timer easy to program/activate. works 24/7 so far to activate a water pumping system i built. recommend.
Valtech
Reviewed in Canada on January 14, 2024
Works as advertised, just hope it lasts a long time….
Bert
Reviewed in Canada on April 16, 2024
Product arrived on time and in good condition.
Daniel
Reviewed in the United States on May 19, 2023
Love this little delay relay. Has so many operating modes. I needed a device that could trigger off a negative signal when my car door is opened for a Siren. This device triggers off a negative or positive signal. I programmed the delay to be on for 5 mintues and is retriggerable. Perfect device and so inexpensive. Could not have found a better one and comes in a plastic case that is easy to mount.
Will
Reviewed in the United States on December 4, 2023
Paired with a smart plug, I am using this unit to control the on-demand mode of my Noritz water heater so that I can control the schedule (smart plug) and frequency (this relay, mode P6) of the hot water recirculation. It works perfectly and avoid the faulty detection system in some models. The best part is that it looks a lot nicer than anything I’d put together!
Mark O'Grady
Reviewed in Australia on June 2, 2022
Works well.
rsb
Reviewed in the United States on January 10, 2022
For the money, this is really an awesome timer...the ONLY thing I would like to see is the "ports" where the wires go into the timer a little larger...using 16 GA wire (110 v) is tight, had to tin the wire to get it all in the clamp...but, it is worth the money....
Recommended Products