Your cart is empty.
Your cart is empty.2002-2005 Dodge RAM 1500 2500 3500 Dash Kit- Harness - Antenna Adapter
Kenny
Reviewed in the United States on February 3, 2025
Works perfectly. Had to modify the radio bracket some so it would fit correctly. Unlike most radio installs the radio goes in then the dash cover. So this does require some cycles of adjustment to get it set with the proper reveal. But it looks like a factory dash. I reused the factory screws for the thermostat control group and the pocket. 10 out of 10 would recommend
AB
Reviewed in the United States on September 25, 2024
The media could not be loaded.
JP Auto
Reviewed in the United States on August 26, 2024
I recently installed the Double DIN Radio Dash Kit with Antenna Adapter & Harness in my 2002 Dodge RAM, and I am thoroughly impressed. The kit includes everything needed for a seamless installation, and the instructions were clear and easy to follow. The fit is perfect, and it looks like it came straight from the factory. The antenna adapter and harness made the wiring process straightforward, and I had my new radio up and running in no time. The quality of the materials is excellent, and it feels very sturdy. Highly recommend this kit for anyone looking to upgrade their Dodge RAM’s audio system!
Dalton
Reviewed in the United States on November 23, 2024
Fits perfectly and pretty easy to install you just need something like a word burner or soldering iron
Vanessa
Reviewed in the United States on June 12, 2023
This item showed up in an Amazon box with all the included parts, so there were no broken tabs or scratches like others had mentioned in their reviews. It was easy to install and had a very nice fit. I started the self tapping nuts with a small impact driver and then finished tightening them with a wrench. I did this to keep them from stripping on the plastic because of the torque of the impact driver. I used this dash kit with a Boss BV9695B double DIN in a 2003 Ram 3500 and the fit was perfect. The only modification I had to do to this kit was to trim the top of "L" brackets that mount to the side of the stereo about 1/4 inch to keep them from hitting the plastic in the dash above the stereo, but it was really no big deal. I would definitely recommend this item and would order it again if I were to do another install.
Carter Devenport
Reviewed in the United States on February 10, 2023
Bit tougher of an install than originally thought. It looks really good and I actually prefer the smooth black finish over the factory rough one. It fit well, but the plastic brackets to mount the radio don’t quite fit so I had to cut some off of the back corners to make it work and it was still a difficult install there afterword. Overall I’d give it 4 out of 5 good quality just hard install. I used the Atoto A6PF head unit with this.
JC
Reviewed in the United States on July 21, 2022
I put a new double din head unit into a 2014 Dodge Ram and it wasn't too much trouble. but I'd say a couple things... this is a flat matte finish on the outside, which is different from what my truck had. My truck's faceplate like this had slight bumps in it, and this does not. So not a perfect match from a finish standpoint. But the black smooth finish looks just fine.Also, I couldn't figure out the nuts that you slide over the plastic things that stick out to secure this plate to the other dash pate, but I used a screw gun and got them started by pushing hard and then I had to snip off some of the plastic sticking out of the middle of the nut because my socket wasn't deep enough. Again, not a big deal, but the directions didn't help with that at all and it took some trial and error. But got it to work and it looks good.Also, the wiring harness does NOT come with connectors, so you will have to go to the store to get crimps unless you have them lying around. You need about 15 of them. Overall a good product.
Terry
Reviewed in the United States on April 24, 2020
The instruction booklet it one page folded in half, and when I saw that I instantly felt like this was going to be harder than I thought. Well, I was wrong. After removing radio surround, you have to use a 1/4" drill bit to drill out the plastic welds to remove the factory radio facia. The instructions say to then use a 3/8" drill bit to widen the holes left from drilling out the plastic welds... I did not do this. Instead I ran the 1/4" bit in and out a few times to make sure the holes were smooth, and that side hole fit perfect with this new facia. Again, I did not use the 3/8" bit. The only hard part was the self-threading nuts that attach the new facia to the surround. I ended up using my impact wrench and some force (but not too much because I didn't want to risk breaking anything) and they all went on pretty easy after that. Definitely could not get them on with a normal ratchet. Great product, looks great in my '04 Dodge Ram 1500 SLT Quad Cab 4x4. I would recommend this to anyone looking to install a double DIN radio. This also came with the wiring harness adapter vehicle specific, and antenna adapter. Both fit perfectly. One thing to note, not all wires from the factory harness may be used on all aftermarket radios. I did not use the "Phone Mute" brown wire. My new radio had no corresponding connection. I simply bent over the end and heat shrinked it to prevent any shorts. And a note: Anyone installing a double DIN radio in the '04 Ram and surrounding years covered by this cover, you WILL have to cut out some of the plastic behind the cover. There is a shelf below where the old radio was that supported it, as well as a top cover area above. I did not need to cut the plastic above (some people do) but I did have to cut out the shelf underneath. I used a small hand hack saw and it went pretty smooth. It is a bit nerve racking when doing it, but if done right, it is so great to see the finished project!
Recommended Products
$17.50
$ 7 .99 $7.99