Your cart is empty.
Your cart is empty.This manual transmission shift lever bushing is designed to match the fit and function of the original bushing on specified vehicles, and is engineered for durability and reliable performance. This part is compatible with the following vehicles. Before purchasing, enter your vehicle trim in the garage tool to confirm fitment. [Toyota 4Runner: 1984, 1985, 1993, 1994, 1995, 1996, 1997, 1998, 1999, 2000] - [Toyota Celica: 1978, 1979, 1980] - [Toyota Corona: 1976, 1977, 1978, 1979, 1980] - [Toyota Pickup: 1979, 1980, 1981, 1982, 1983, 1993, 1994, 1995] - [Toyota T100: 1993, 1994, 1995, 1996, 1997, 1998] - [Toyota Tacoma: 1996, 1997, 1998, 1999, 2000, 2001, 2002, 2003, 2004] - [Toyota Tundra: 2000, 2001, 2002, 2003, 2004]
Michael R
Reviewed in the United States on July 28, 2024
Replacing these bushings made a huge difference for the way my '94 Pickup shifts. I didn't even realize how bad the original bushings had gotten. I only have about 150k miles, but the original bushings were so disintegrated that it was actually hard to get the remnants out without dropping pieces into the transmission. Anyway, replacing the bushings made the truck a real pleasure to drive again.
K. A.
Reviewed in the United States on July 27, 2024
I needed the Bushing on the ball most so 1 of the two worked .. get Toyota stay away from Dorman
Devil's Hand Diesel
Reviewed in the United States on May 5, 2024
This fits the 1985 Toyota pickup w56 transmission.Installed and works perfectly. Seems to be good quality but I figured I would order one every time I change the fluid.
Ivan
Reviewed in Canada on February 14, 2024
Fits well on Tacoma. Replaced original. After 20000 km no problem so far.
Jamieson
Reviewed in the United States on November 27, 2024
Installed this in a 1998 Tacoma 2.4L 5 speed and was blown away by how bad the original bushing was. The smaller white plastic bushing was completely fine. But the rubber/composite black bushing looked like crumbled up bits of brownie in the turret. I used a shop vac to get all of the bits out and pried out the remaining ring using a pick. The new bushing went in easy and the shifter locked into place without an issue. Whole job took maybe 15 minutes. The difference in shifts is night and day now
Shaun
Reviewed in the United States on January 31, 2024
Worked in my 1998 Tacoma 5 speed. 2.7 liter engine. 4x4. Dorman always makes OEM quality stuff. I trust their brand. This was no surprise. It has worked perfectly.
Stirringro
Reviewed in the United States on January 31, 2024
Easy to install and improved the shifting experience dramatically!
K-So
Reviewed in Canada on October 1, 2023
98 tacoma, fits well, didn't completely resolved my shifting issue but significantly improved it. recommend changing yours as easy maintenance item rather than when things starts to failed.
Rod in Forfar
Reviewed in Canada on November 6, 2022
The videos slightly underestimate the difficulty of this job, but when the kit is re-installed, it is as if the truck is new again. Lacking the joint strength to force the spring back into place, I resorted to hitting it sharply with a hammer. That worked perfectly. I had stumbled onto the trick the video guys didn't show.
T. Mackey
Reviewed in the United States on November 13, 2020
Was having the "stubborn to go into 1st and 2nd" problem. This took all of 20mins to install, and I went the extra step to take the plate off and make sure things were clean below it. Without that, just take off the shift knobs, center console shift cover, push down and 1/4 turn the retainer, and pull the stick out. The old white plastic end bushing on mine didn't look warn, but was yellow/brown and very tight fit/didn't want to move. Took some effort to get off without scratching the ball. New one popped on fine, lower ring bushings were simple to swap. Added a little grease to them and buttoned it back up, shifts like new again!
Shannon S.
Reviewed in Canada on January 24, 2019
The press on bushing does not fit my Toyota t100. The bushing cracked when trying to press it on. The seat however, was a perfect fit. Ordering Toyota parts.
Bendigo Noble
Reviewed in Canada on April 2, 2019
my 93 yota pickup needed this
HRomero
Reviewed in the United States on March 17, 2017
good quality materials but THIS WILL NOT FIT A 1997 TOYOTA TACOMA 4X4 EXTENDED CAB! Amazon says it will with their "check if it fits" feature but it will NOT fit a 1997, Dorman, O'Reilly, Autozone, Pep Boys and other vendors also say it will fit but i can assure you that it will not. there may be other 1st generation Tacomas that it will fit maybe others will chime in. When i tried to press it on it split, ended up calling around and finding the OEM part at a local Toyota dealership, the bushing is slightly bigger allowing for a press fit. The seat included in this kit fits just fine and looks exactly like the OEM part. Thank goodness Amazon has a great return policy and i was able to get a full refund. To their credit they probably rely on the manufacturer's information so it's not Amazon's fault.
Recommended Products
