usb c to sny multi cable

1. Multi function camera control line For sony(USB-C TO Multi) 35cm/13.7in
2. Note to buyers: This cable can be used for all DJI camera hand stabilizers (not supported by the ronin-s generation), but does not support the stabilizers to power the camera
3. Applicable equipment: for DJI stabilizer（Ronin-sc,Rsc2,Rs2,Rs3,Rs3 PRO,RS4,RS4 PRO,dji focus pro)
4. Apply to the camera:for sony - a7,a7m2,a7m3,a7m4,a7s,a7s2,a7s3,a7r,a7r2,a7r3,a7r4,a6000,a6100,a6300,a6400,a6500,a6600,a9,a9ii.ZV-1.rx1r,RX1RII .RX10M2/M3/M4,RX0,RX0II,RX100M2/M3/M4/M5,A500,A5100,A5300..
5. Support control functions: focus, photo, video, zoom
6. DJI stabilizer operation method: half press the red button - focus, press the bottom stop for 2 seconds - take a photo, directly press the bottom and let go - video.
7. Zoom Method: Find "Zoom Method" in the SONY camera menu - select "Digital Zoom" and set the stabilizer's wheel operation function to "Zoom/follow focus". This allows you to zoom in/out of the camera while rotating the wheel

Camera setup note:

1) Before connecting the cable, go to the camera menu and set the "USB&" of the camera. After the connection mode, the communication can be normal. As shown - select "Computer Remote Control"

2) After setting, plug in the cable, turn on the stabilizer power, and then turn on the camera power, and then you can directly control the camera and video operation.

3)Operation Procedure Description:

01)- Set the camera usb as the computer remote control --a. Turn off the "Use Smartphone Control" camera menu. The detailed setting method is as follows: Choose: Menu > Network Use a smart phone option is off.

b. Set the USB Connection function of the camera to Remote Control. specific The setting method is as follows:

Old menu: Setup a select USB connection a select computer remote control

a.New menu: network > transmission/remote a ? computer remote control function a open; Or a network ? computer remote control function on.

02)- Plug in the cable, turn on the camera power, you can control the function. (Points for attention)

a): To ensure that the stabilizer can correctly identify the sony camera, power on the stabilizer first and then the camera after connecting cables.

b): When paired with a lens with (Power Zoom) function, optical zoom can be controlled; If a lens does not have the Power Zoom function, you need to enable the digital zoom function of the camera to control the digital zoom. The detailed setting method is as follows: Select Menu Select Settings Select Zoom Settings Select digital zoom.

c): If you need to switch to another camera control cable after connecting with MULTI cable, restart the power supply to stabilizer ensure normal function.

Stabilizer camera connection cable port location

Stabilizer camera connection cable port location：

• 1）Ronin-sc: The camera port -Type c is located in front of the pitching shaft mounting plate
• 2）ronin-rsc2:The camera port -Type c is located behind the pitch shaft mounting plate--RSS
• 3)Ronin-rs2/rs3/rs4 Camera cable control port Location "RSS"：At the front and back of the horizontal roller, a socket marked "RSS" and camera pictures.
• Fault 1: If the plug is inserted into the wrong port, there will be no response. Because each Type-c port on the stabilizer acts differently.
• Fault 2: Confirm that the plug position is not wrong, the camera does not respond, please re-unplug - plug the USB C plug and turn the camera on again.

Camera port precautions

1. Description: for sony camera port "MULTI" For the multi-functional USB data plug, the internal is divided into the first 5pin after 10pin a total of 15in, and ordinary Android plug "Micro usb 5pin"; Different. The MULTI plug will be longer, so it needs to be pushed into place when inserting the camera to establish a connection.
2. This port can charge the camera and connect to a computer with a regular Micro usb cable, but it can't control camera shooting.
3. Troubleshooting:

1- Does the camera not react after connecting the stabilizer to the camera cable?

A- Check that the stabilizer port is inserted correctly.

B- Check that the camera plug is pushed to the terminal clamp (with lock) position.

2-- The camera screen will display "USB connection" or "unable to connect"

A- If you set the USB as described above, it will still show a screen that cannot be connected. Please turn off the camera power and turn it on again

B- After selecting USB as "Computer remote control" in the camera, the USB connection is still displayed, which should be the problem of the cable, and a new connection cable needs to be replaced

3- Can control photography, video, but can not zoom?

A- Unplug the cable, go to the camera menu, find - Zoom Mode - select "Digital Zoom"

B- Press and hold the round pull wheel of the stabilizer, and set to "Zoom" and "Focus" when turning the large round wheel on the DJI in the display on the stabilizer.