Your cart is empty.
Your cart is empty. Water Temp Gauge Radiator Hose Sensor Adaptor Temperature 26mm 28mm 30mm 32mm 34mm 36mm 38mm 40mm
Features
Size: 26mm 28mm 30mm 32mm 34mm 36mm 38mm 40mm
100% Brand New.
Color:Blue,Red,Black,Silver
Fit For Auto Meter water temperature gauge,glowshift water temperature gauge,Defi water temperature gauge,Depo water temperature gauge ,VDO water temperature gauge and so on High quality
Manuel
Reviewed in the United States on March 2, 2025
It’s the right fit for me jeep yj I love it
Steven Webb
Reviewed in the United States on September 1, 2024
I used this to convert my son's 2011 Nissan Frontier from mechanical to electric cooling. It couldn't have been easier to install, and is still working leak free months later. Great product, especially at this price point.
Dawson
Reviewed in the United States on March 19, 2024
It is made of softer aluminum and you can strip threads if you aren't careful. Other than that it works great. I used it as a coolant drain and a 2nd one as a distribution for a coolant pressure sensor (never know when a head gasket is going to go) for my turbo BMW E46 325ci. This thing works great, doesn't leak so long as you use coolant-compatible sealant on the threads and properly torque them, and comes with 2 hose clamps. Make sure to tighten the hose clamps with a ratchet and not just a screwdriver- screwdrivers slip and don't put enough torque to hold a coolant hose together under the pressure a cooling system is at while operating.
Mark adams
Reviewed in the United States on December 22, 2024
Splice was easy to install. Good quality build lightweight and worth the price. No issues of any kind other than a very vage set of installation instructions. The instructions need to be a little more informative then what they are. The description of the product needs to be revalued and better described. The description needs to point blank state weather it uses a electronic sensor or a manual sensor. Overall a great product
William
Reviewed in the United States on November 5, 2024
Sizing was a bit snug. Seems well made. Does what it's supposed to. No leaks. Fans turn on and off like they're supposed to. Don't forget that it needs to be grounded separately.
Customer
Reviewed in the United States on January 1, 2024
So I wish I had seen the other comments but when measuring for the product size, I measured ~38mm on my CJ5's radiator. With that, I ordered 38mm on the part. The part actually measures just over 35mm on the pipe's OD even when you order 38mm. Apparently 38mm refers to the flared portion at the end. Since your cooling system can be under pressure in a closed system, this is dangerous and could randomly separate or over-compress the hose if I were to use this.I ordered the next size up 40mm and it will be here to complete the project (hopefully). Outside of that, this product looks decent and will do what I need it to for my 2 speed radiator fan install.
Ing Manuel Salas
Reviewed in Mexico on March 23, 2023
Muy buen material y muy buen acabado. Pieza simple para un proposito especifico el cual cumple perfectamente.
Arsenio C.
Reviewed in Mexico on October 25, 2023
Lo instale en la manguera del radiador con unas abracedaras y lo conecte a un marcador y me funciona bastante bien
Carlos Manuel De La cruz Perez
Reviewed in Mexico on January 4, 2023
Es Perfecto , gracias
Emmanuel Mora
Reviewed in Mexico on May 2, 2022
Excelente calidad excepto por las abrazaderas que vienen en el kit al apretarlas se barrieron y tuve que cambiarlas, y al colocar el sensor por mas que lo aprete seguia tirando agua cuando el sistema aumentaba la presion (nada que un poco de silicon no solucione, solo que hay que tener cuidado de no poner demasiado y aislar el sensor ya que no funcionaria),todo lo demas quedo bien.
Beth Beeson
Reviewed in Canada on February 22, 2021
Quality products, as advertised, arrived as scheduled. Happy with the purchases
Cooper
Reviewed in the United States on December 20, 2020
My opinion and experience with size selection (review at the end):You want a snug fit (a little resistance when attaching the hose). Measure the inside diameter of the section of the hose you will be splicing it into. If that isn't an option because you'd have to cut the hose and you can't have your car down for a couple of days, then measure the outside diameter and subtract the thickness of the hose wall X2. Based on the measured inside diameter of the hose, select the adapter that is the next size up (+2mm). You may be able to get away without going slightly up in size, but the clamps will really have to bring it down and while it might not leak, the seal wouldn't be the best. USE YOUR OWN DISCRETION this is my personal recommendation based on my experience:The ID of my radiator hose was approximately 31.7mm and at the very least you should round that number up, so I ordered a 32mm adapter. Upon fitting it, it was appropriately sized, but it wasn't a snug fit and without clamps it would easily fall out. I was concerned about the seal because of how much you would have to tighten the clamps. I decided to order a 34mm and it worked out great. I could have easily used 36mm as well, but since my radiator hose was not new I left room to take into account that my old hose was probably expanded slightly. Great time to just replace the whole hose! Even though you may have to cut it depending on your application.Installation Review:Installation was easy. You will need to make a small grounding wire to attach from the small screw on the adapter to somewhere on the car frame or engine. If you have them, you may want to use hose clamps that are a little beefier than the clamps provided. I used this with an aftermarket Bosch water temp sensor and gauge, using Teflon tape on the sensor threads before installing it into the adapter. I cut out a small section of the upper radiator hose (hot side, using razor blade) to install the adapter. I would install it as close to the engine water outlet as you can. After installation be sure that none of the modified hose sits above the top of the radiator in order to help keep air from getting trapped in the system.One month after install:Everything is perfect. Great product.
Octathorpe
Reviewed in the United States on August 12, 2017
The anodized aluminum body of this part is really nicely machined and finished. The ground screw is also handy. It really works very well for adding a temp sensor with 1/8" NPT threads to your radiator hose. The reasons for only three stars are: 1) the diameter of the part is not really equivalent to the inner diameter of the hose that the part fits. The 'nipple' on the end of the connector is equal to the part's stated diameter, but the flat part of the tube behind this nipple is less than the part's stated diameter. This means if you have a 34 mm ID hose and buy a 34 mm ID part then the part will be too small. You want the flat part of the connector area to be equal to the hose ID and so you have to add 2 mm (the height of the 'bump' at the nipple) an order a 36 mm ID part. If your hoses are older and a bit stretched you may want to get even larger like 38 mm. Measure your actual hose and buy 2mm larger than that. I had to order and return and re-order to get one to fit. And loss of star # 2) the hose clamps are not very good quality. They are thin in the width and not very thick. I had trouble getting them to seal once the radiator hose had built up pressure. I had to replace them with "proper" stainless steel band clamps since I don't want this temp sensor to be a weak link. SO, buy this part and use your own clamps and get the one that is labeled as being 2 mm larger than the actual measured inner diameter of your radiator hose.
Recommended Products
