Your cart is empty.
Your cart is empty.The DEWALT DWA2600IR Impact Ready Conduit Reamer is designed to make quick work of de-burring EMT conduit. Works in sizes 1/2", 3/4", and 1" conduit. Has a 1" bit tip holder on the front of the unit, for tightening fittings and driving screws. This is an IMPACT READY hex shank for use in high-torque Impact Drivers.
John Brownell
Reviewed in the United States on February 17, 2025
Great for conduit reaming jobs just connect to your 1/4" driver and use with the simple push of a trigger no more hand cranking the older style. This way is so much faster you can not compare them at all.
James Ess
Reviewed in the United States on July 13, 2024
I like this a lot. This is so neat. The blade is spring loaded as retracted. When you use it press into the tubing and the cutter blade extends and removes the burrs. Just a few revolutions and the emt tube is smooth as can be. This makes a great gift. New replacement blades are available on Amazon.
lovepickingnc on eBay
Reviewed in the United States on February 21, 2024
Works great with a DeWalt drill.
Ian bob
Reviewed in Canada on January 9, 2021
Fonctionne très bien et est impressionnant mais attention à ne pas utiliser sur du cuivre, chauffe beaucoup et la vis de soutien à simplement sauter, je la cherche toujours car ma lame est encore bonne
Ryan Campbell
Reviewed in Canada on August 23, 2020
Great tool
Dustin Labrecque
Reviewed in Canada on July 29, 2019
4th conduit reamer over 5 years in the trade.1/4 drive is thicker then the klien reamer.Allows you to save it if your impact takes a fall from the ladder, Dewalt reamer survives better.The spring loaded sheath also is handy for taking down sharp teeth after a rough cut.Only one I tell apprentices to get.
John S.
Reviewed in the United States on July 9, 2018
The Dewalt reamer works the best of any I've used. I ordered this specifically for the large job and used it for 3/4 and 1 inch EMT and it worked perfectly. I like how it's spring loaded, so the blade only is out when it's pressed against the tub being used. The interchangeable tip is also nice for quick transition from reaming to securing the connections without having to have 2 drivers or change the tip out all the time.
Gabe
Reviewed in the United States on November 18, 2018
Between the blades catching constantly, and the pressure you have to use to push back the spring, it wears out my hands faster than using traditional handheld reamer. One or two quick turns with the klein reamer will work, where this one I feel like I have to really work it to get a clean conduit. I use this on my screwdriver handle and with a drill, and that was the appeal, smaller tool and half the price, and for that its good.
JD3619
Reviewed in the United States on October 25, 2018
This product reams so sell that I would say it does a better job that the factory end on EMT. One piece of advice I have though is to buy a couple of extra blades and throw them in your tools because they are harder to find and its inevitable that you will break them. I've gone through as much as 1 reamer blade once a month on a job with a lot of pipe work but its worth it. It does an incredible job, saves a lot of time, and most importantly it saves wear and tear on my wrist.
john young
Reviewed in Canada on February 11, 2016
Works great but the Robbie head gets stuck in the screws. I wish I locked in better. Be careful using an impact gun it fired swarf everwhere
SWCanadian
Reviewed in Canada on November 6, 2016
Works great. I was hesitant at first cause some reviews said it broke easily. It's not the case, I never ran my impact full blast, I had it one setting 2 and ran it on that and it's been working perfect
The General
Reviewed in the United States on November 20, 2016
I am going to give this a middle of the road review. I found complications with the product that are specific to my tool/work set up. So your mileage may vary here. I use this tool in commercial electrical work with an M18 FULE v2 Impact driver on #2 power setting (1500 rpm), and a metal cutting saw that produces little to no burrs but can leave one large tassel on 3/4 EMT periodically. I can say that I have broken two of these my own and a co-worker's (sorry bud), with my impact, both of them the tools blade broke off. His version was a non impact rated and bought at home depot, while mine was purchased here. That being said he and others that use lower power M12 or Dewalt tools have NEVER had an issue. I believe that the high torque and impacts of new hi power tools may be an issue, beyond this I have been pleased with the design, price and utility of the the tool.Pro: What I love about this tool is that it's blade retracts inside the sheath making it less likely to snag on tool bags/ gloves and providing an extra measure of safety and convenience.Con: Tool may not be strong enough to handle M18 2 gen tools and Dewalt 24v on high settings.I can and do recommend this tool to others but they are using lower power tools than I. I am replacing this and using a lower setting or smaller battery pack from now on.
Boomersays
Reviewed in the United States on August 26, 2015
This is a really well engineered and quality tool. I'm using it with a Milwaukee M12 impact and it really does ream and screw well. I can't say enough good things about it.The reaming blades are covered when you are using the screw tip. When you want to ream a pipe out you just push it in and the cover over it is spring loaded and it pushes back exposing the reaming blades.Very well thought out and very well executed. Dewalt is really stepping their game up as far as being innovative.
Recommended Products
