Your cart is empty.
Your cart is empty.Product Description
Mark Gerstenlauer
Reviewed in the United States on February 8, 2025
Never use a 2-3 ton hydraulic jack on your vehicle that has a flat puck without this.This will save you punch welds so that if you ever need to use the factory jack on the side of the road it will work correctly. Have used this for years, still like newI grade aluminum with plastic insert, I never jack without it.
CummApart
Reviewed in Canada on February 2, 2025
It is as advertised
SEM
Reviewed in the United States on February 16, 2025
Looks like it will work Ok. Only issue was the diameter of the device was too small for the cup on my jack. This allowed it to sit 3/8" too far down and the outer edges of the cup would still be hitting the body of the car. I simply made a couple of spacers out of 3/8" thick aluminum to place under the device and raise it up above the outer edges of the cup. This was actually my fault for not measuring the size of the cup on my jack before ordering the adapter.
F
Reviewed in the United States on January 3, 2025
Works great on my 392 with a quick jack. Magnetic feature is very helpful.
Customer
Reviewed in Canada on September 29, 2024
Used this on our EV and it wasn't strong enough to handle the weight. After hearing two cracks I lowered it to find bench side walls and pinchweld grooves. Seller should put weight specifications on product.
Anthony
Reviewed in the United States on July 5, 2024
This is great for those cars that have jack points on the pinch weld. Nothing really to say about it, it just works. However, be aware that it's magnetic. When raising a car, you are often at floor level locating the jack and the magnets really help with this. But when you lower it, you're usually standing up, lower the jack and pull it away from the car. Several times we've forgotten to remove this pad, but fortunately it stayed in place even after driving!
Kenneth
Reviewed in the United States on February 12, 2024
I recently bought a Quickjack 5000TL. I have a 2018 Jeep Compass Latitude 4x4, which has pinch weld lift points. I bought four (4) of these to save some money compared to spending almost 90 USD on Quickjack's rubber pinch weld blocks. (Yes the Jeep has flat lift points, but they're inside the wheel base rather than along it like the pinch weld points.)So a couple things about my experience.1. Put them on the vehicle first, then lift the Quickjack to meet them. They're magnetic, so will stay in place. And orange, making them stupid easy to see when lining up the Quickjack.2. These are 2.7" wide, and the Quickjack rubber lift blocks are 3" wide. So they spread out the weight onto nearly the full width of the rubber blocks, so don't compress the rubber. Meaning...3. Don't worry about leaving the vehicle lifted. I (unintentionally) left my Jeep lifted on the QuickJack for a few days and these showed no sign they were going to fail after I brought them down. And these didn't slip or slide on the rubber blocks.So, in the end, absolutely recommend using these if you have a Quickjack. Again, just remember to put these on the vehicle's lift points before raising the Quickjack to meet it. I'll probably also follow Herbie's lead and add something similar to his "Remove Before Flight" tags to these before using them again.
Garnet Austen
Reviewed in Canada on November 29, 2024
Good protection for your car. The magnet is so strong that when I forgot to remove it from the car, I drove around for 30 min and it didn't fall off!
Alex Cook
Reviewed in Canada on November 17, 2024
Holds itself in place at the jack points on the "frame" / body of my wifes Mazda CX5, nice and strong sits on my jack when not in use.
Brad
Reviewed in the United States on October 30, 2024
The jack pad worked great protecting both my Subaru Forester and Toyota Sienna, as well as my hydraulic jack. Magnets held it in place as I adjusted the jack underneath it and applied pressure. In my case the jack pad fell off easily if bumped, which might be good because you also need to be careful about not forgetting it is there and drive away with it still attached.
JOSE MIGUEL VALDEZ LOPEZ
Reviewed in Mexico on October 17, 2024
solo está magnetizado en la ranura para la adaptación a la ceja de soldadura, pensé que estaba magnetizado por debajo para un mejor agarre con el gato del vehiculo, la ranura queda un poco grande sobre la ceja de la soldadura pero funciona bien y si ayuda a evitar el maltrato del vehiculo al usar gatos hidráulicos
A
Reviewed in the United States on November 3, 2023
Especially, if you're like me, and you have a Chevy Camaro with little body left to raise the car up after the jack is in place. This thing fits perfectly on a pinch weld. It is essential for displacing the pressure when raising your automobile using a lift. Otherwise, the lift or the body are likely to incur cracks and breakdown. Also, this is the best one I have found where low price meets high quality. And loving the magnetic function. Excellent product.
Chris Green
Reviewed in the United States on May 10, 2019
This is really a life saver, if you work on your cars a lot and it requires lifting them up, buy one or 4 of these. It really does a great job protecting your pinch welds and is the perfect size.To attest how strong the magnet is on this really is, I might have forgotten it on the underside of my car after doing the brakes. A few rainy days went by and about 200 miles later I remembered it under there and it was still attached... whoops!My only complaint is the magnetic part (see the white plastic piece in the photo) came apart from the actual jack on mine. I ended up super glueing it back on and it works just fine now.
Recommended Products