Shopping Cart

Your cart is empty.

Your cart is empty.

DC 12V-36V 15A 500W Brushless Motor Controller, DC Motor Speed Controller, Hall BLDC Control Board, Brushless Motor Regulator, Durable and Stable Performance

4.5 (6) Write Review
Free shipping on orders over $29.99

$17.36

$ 6 .99 $6.99

In Stock

About this item

  • 【High Quality】The brushless motor controller is made of high quality metal, durable, not easy to damage, has good performance and long service life
  • 【Feature】 DC motor speed controller is compact design, easy to carry and store, very convenient in life, can improve work efficiency, save time and energy
  • 【Stable Performance】 DC brushless motor regulator is easy to operate, with stable performance, if you are looking for high quality, it will be the ideal choice
  • 【Product parameter】 The size of the motor controller is 63 x 42 x 17 mm (L x W x H), the size of the probe is 3 mm, length: fixed hole distance 57 mm; width: fixed hole spacing 36.5 mm
  • 【Quality Assurance】 This speed controller is manufactured according to strict quality control and standard requirements, and has a high safety factor, so it can be used with confidence


Specification:
Operating voltage: DC 12V-36V.
Operating current: Driver power: Speed voltage: 0.1V-5V.
Operating temperature: -40-85°C
Humidity: 90% RH
Stall protection: yes.
Enable control: Yes
Overcurrent protection: Yes
Steering control: Yes
Speed control signal: Yes
Size: 63 x 42 x 17 mm (L x W x H); Probe size 3 mm, length: 57 mm hole spacing; width: 36.5 mm.
Wiring:
Control terminal for SET:
1. Motor speed control wiring methods: The speed of the available potentiometer system can also be connected to MCU control, when the potentiometer control wiring, the center pin of the potentiometer is connected to the VR speed port, the potentiometer connected to both ends of the terminal voltage 5V and GND higher speed faster.
2. Motor direction control wiring methods: you can switch the control can also be connected to MCU control, to GND in one direction, and then in a 5V direction.
3. Pulse speed signal: high and low output. IC cannot understand the information with the customer's request.
Package includes:
1 x 12-36V 500W Brushless Motor Controller


Gabriel alassia
Reviewed in Spain on August 13, 2024
he comprado 2 y ninguna funciona
tony horton
Reviewed in the United Kingdom on December 16, 2024
Burnt out immediately
jesus morales
Reviewed in Mexico on November 27, 2024
Pequeño, práctico y funcional, pero, no me gusta que no trabaje a 48v, no tiene disipador, ni conexiones de control, se las tuve que soldar yo y agregar un disipador. En general cumple con lo mencionado.
Car
Reviewed in the United States on November 19, 2024
Did not work. Immediately broke. I was very carful installing it, even went through the trouble of attaching a heat sink. Still malfunctioned. Maybe I just got a bad one either way I’m not going to spend the money to find out.
Simon
Reviewed in Sweden on April 24, 2024
Have bought 3 of these. Two of them was malfunctionakl. The third one died after 1 min use. Totally crap. This is a scam.
Christin Großmann
Reviewed in Germany on March 2, 2023
Ich habe jetzt schon den zweiten Controller in der Hand. Beim ersten waren alle Fets falsch herum eingelötet. Daher habe ich diesen zurück geschickt und extra bei einem anderen Händler einen weiteren Controller bestellt. Das gleich Spiel. Alle 6 Fets sind falsch herum eingelötet. Da ich das Ding brauche und nicht noch mehr Zeit verlieren wollte, habe ich die FETs selbst gedreht. Nach ein paar Sekunden Motordrehung bei 24V ist die Platine dann schließlich völlig ausgestiegen und ich kann das Ding in den Müll werfen.Ich war schon skeptisch durch die vielen anderen Bewertungen. Da die Alternativen fehlen, habe ich doch bestellt. Leider hätte ich das Geld auch gleich verbrennen können. Ich habe bereits viele Platinen aus China verwendet, von denen einige ihre Problemchen hatten. Das Zeug hier ist dagegen der blanke Schrott. Sorry...