Your cart is empty.
Your cart is empty.Product Description
CARLITS DRL LED STRIP
Real shot from us
Our lights are brighter. Each light bar has more than 100 white and yellow light leds, and there is no dark area.
Real shot from customers
Sequential turn signal light 01
Yellow light 1th step
Sequential turn signal light 02
Yellow light 2th step
Sequential turn signal light 03
Yellow light 3th step
DRL white light
Customer said:
'This product didnt have any reviews, but I thought I'd give it a try as I like that its slim ne how the light beam comes from the side vs the top. I was initially going to install it inside my headlight, but my headlight eyebrow is attached to both my height and turn signal lens and I was concerned it might break trying to remove it. I went with the other option which this product also recommend which is to install it between the headlight housing and the hood. It actually fit really good and you dont notice it when close up to the car when light is off. The light is bright e ough that it's still visible during day light and the turn signal light runs across vs illuminating all at once, so you will want to check how you install it as they are packaged as left and right due to the turn signal motion. You want it to run towards the side you are turning.'
Can be cut as you need
Measure the size before installation, and then cut the appropriate size. Note.: Re-attach the plug with glue.
Installation suggestions from my customer
Install and wiring notes: I decided to use and installed a 'fuse tap - 10 amps max' (see pic 2) on to my existing ACC fuse. I then connected the fuse tap red wire to to 18 gauge red primary wire that was run through the firewall into the engine area, ran along one side of the engine area, long enough to reach both headlights. I used velcro to keep the wires neat and out of the way. Both LED light wires (red) were spliced/soldered to this red primary wire. Note that each light is around 1amp, so a very fractional amount of amperage needed. The LED light wires (black) were spliced/soldered to 18 gauge black-colored primary wire and ran to the negative battery cable frame bolt and connected to the bolt with circular terminals. The LED light wires (yellow) were spliced/soldered to the turn signal light positive cable, to allow for the synchronized turn flashes.
3 wires connction show
1,Red line to ACC +
2,Yellow line to turn signal +
3,Black line to battery -
Non-destructive installation
Car headlight surface instllation
Wipe the surface with a clean cloth, tear off the back sticker and install it on the surface of the car headlight.
If necessary, you can use glue to assist the installation, which is more reliable.
Real shot from customer white daytime running light.
Real shot from customer yellow/amber turn signal light
Customer said:
'I get a lot of compliments on these lights. As many have said, they are not bright during the day, but I use them as a DRL and love the way they look during hours of low light or dark. No fault to the light, but I was unable to use the sequential turn signal, due to my truck having LED and no where for me to tap that wire into. Kinda funny, but even though the wire to the amber light is cut and taped off, but you can see in the picture that the first night of install, the light briefly turned amber. This doesn't happen often, nor does it bother me. All-in-all, I really like these lights and would definitely buy again.'
USMC
Reviewed in the United States on March 6, 2025
absolutely great seller, price, communication, item exactly as described or better, promt safe delivery. I highly recommend this seller and item. A++++++++ 5 Gold Stars!!
Kelli Price
Reviewed in the United States on February 19, 2025
Easy to install, however only lasted about 4 months before leds began to fail inside the wire.
Phil B.
Reviewed in the United States on January 28, 2025
The media could not be loaded.
Customer
Reviewed in the United States on May 17, 2024
I don't normally write reviews unless I am very impressed with something are very unsatisfied. I am very impressed with these lights. I install them on my Ford F-150 pickup just for the DRL lights. They are very bright and seem to be good quality. Yes you have to use something other than the glue if you bend them around. I use some gorilla duct tape behind it and it held very good. I am just using the DRL bright lights and not the turn signals, but they were easy to install and seem to be great quality. We will wait to see how they last.
Brandon Thai
Reviewed in the United States on December 30, 2024
The media could not be loaded.
N8
Reviewed in the United States on December 29, 2023
The media could not be loaded.
QT
Reviewed in Canada on December 11, 2023
The media could not be loaded.
Christopher Moran
Reviewed in the United States on April 19, 2023
The media could not be loaded.
Francesco
Reviewed in Italy on March 18, 2022
Facile installazione
CJ
Reviewed in the United Kingdom on December 12, 2022
Very nice quality item and well packaged. Not fitted mine yet waiting for the engineer, but the length is just right to cover a large headlight unit in an L shape. One thing I will do however is add another strip of 3M two sided sticky tape. I buy it from Amazon too. The strip lights can take a fierce head on weather like snow and ice, so I'm going to double up on adhesion just to be on the safe side.
207 du 84
Reviewed in France on September 21, 2021
Eclaire très bien mais demande un minimum de connaissance en électricité car j'ai dû créé un faisseau pour les feux de jour et pour le clignotant il faut le brancher sur la cosses du phare à l'emplacement du fil du clignotant pour le raccordé
Belgie
Reviewed in the Netherlands on June 22, 2021
werkt perfect met IC decoder.mijn vorige waren zonder en die werkten niet zo als verwacht. Gemakkelijk te monteren en af te knippen volgens lengte.
Nicola Lopez
Reviewed in the United States on March 18, 2019
The media could not be loaded.
Recommended Products