Your cart is empty.
Your cart is empty. This page features 1 piece super bright 30 SMD 5050 LED Strip used to replace the center trunk or cargo area lamp to light up the entire trunk area
It is only recommended to replace the trunk/cargo area lamp located in the middle of the trunk for max lighting output effect Fitment
There's one T10 and one size adjustable festoon adapters in this package which will fit any wedge and festoon housings including:
168/194/2825 wedge housings
Universal fit
Acura MDX RDX RL RSX TL TLX TSX
Audi A3 A4 A5 A6 Q5 Q7
BMW 1 2 3 4 5 6 7 series X1 X3 X5 X6 Z4
Cadillac CTS Escalade
Chevrolet Avalanche Camaro Colorado Cruze Malibu
Dodge Avenger Caliber Challenger Charger Dart Durango Neon Ram
Ford Edge Escape Explorer F-150 F-250 Fiesta Flex Focus Fusion Mustang
Honda Accord Civic CR-V CR-Z Fit Pilot Ridgeline
Hyundai Genesis Santa Fe Sonata Tucson
Infiniti EX35 FX35 FX45 FX50 G35 G37 M45 M35 M37 M45 M56 Q50 Q60 QX60 Jeep Grand Cherokee Wrangler
Lexus CT ES GS GX HS IS LS LX RX SC
Mazda 2 3 5 6 CX-5 CX-7 CX-9 Miata RX-8
Mercedes C CL CLA CLK CLS E GL GLA GLK ML R S
Nissan 350Z 370Z Altima Cube Frontier Juke Maxima Murano Rogue Sentra Titan Xterra
Scion FR-S FRS tC xA xB xD
Subaru BRZ Forester Impreza Legacy Outback WRX STI
Toyota 4Runner Camry Corolla FJ Cruiser Highlander Land Prius RAV4 Sienna
Volkswagen Beetle CC Eos Golf GTI Jetta Rabbit, etc
EV4Life
Reviewed in the United States on September 8, 2024
2022 M3LR, plugs directly into the connector for the passenger side trunk light (had to loosen retaining tab from C pillar to gain more length). Applied directly over metal at the very end of parcel shelf. Amazing lighting, lights up the driveway behind garage. Best accessory in a while.
Manuel Marquez
Reviewed in the United States on May 7, 2024
Thankfully Im an Electrician so i was able to modify the cable a bit.Used it to put more light in the trunk of my car and i can see Everything in my truck!! Pretty good lights for the price. Just be prepared to do some modifications lol.
Timothy Perez
Reviewed in the United States on March 1, 2024
The install was very quick and easy and it definitely brightens up your trunk. The materials are cheaply made though. The little wire connectors have a poor connection, so I have to slightly tug on the wire a certain direction for the light strip to turn on.
Y.P
Reviewed in the United States on January 23, 2024
I'm plenty satisfied, very bright at night and barely noticeable if installed properly. I liked the adhesive backing. The spare connectors came handy while installing in the trunk of my 2014 F30/320i. I placed electrical tape at the far ends of the tips kept bending upward slightly; this will keep them from accidently getting snagged while loading & unloading materials in the trunk. Good purchase at a reasonable price.
Joe R.
Reviewed in the United States on November 1, 2022
I really wanted to love this item, and I'll be the first to openly admit that it makes the trunk space super bright, but I can't overlook how it was poorly made. The wiring and 168/T10 connector is shoddy at best, and was a JOKE! The 168 connector was held on by a single strand of 24 awg aluminum bent over. The wires broke off when trying to install it into the light socket.Now this left me with 2 options, return this broke item (and get a replacement just as bad) or fix their design flaws and make it work. It was easier for me to fix their design flaws.I replaced their wiring with 16 awg speaker wiring I had. It was easy to solder them to the positive and negative terminals on the 5050 LED light strips. Then I used 2 snap wire connectors on the light leads and everything worked great.I am greatly disappointed with this as it could have been a great product. It has potential, but needs better wiring and 68/T10 connector. With as much work as I had to do to make this "work" because of their design flaw, I would have been better off making it myself for cheaper. VERY DISAPPOINTED in it's wire quality!
The Hunters
Reviewed in the United States on May 16, 2019
Installed in a 2018 Kia Forte. When the package came, I guess I thought it would be larger. It is a small box. The first few pictures compares the size to a few quarters. While the whole package is small, it provides decent light for the trunk. There are no instructions but, it is not too complicated to figure out if you can replace a lightbulb. Here are a few technical details about the product:The strip is about 19.5" inches long. About half way down the strip is a soldered-on pigtail at the 10" mark. The pigtail is about 2.5" inches long.There are 30 LED's on the strip (specified in the product description as well). They are of the 5050 SMD design. LED strip has foam-based sticky tape for better cohesion (as opposed to normal LED strips).The kit comes with two connectors and an extension wire.Festoon type spring load plug and pin type plug. Connectors are 2.5" inches long.Extension wire is 12" long.The festoon bulb is what I had and used the festoon connector. The LED strip is polarity-sensitive, so test which direction the festoon connector should go in.In my case, the existing light was in the center of the trunk, so did not need the extension wire. Everything tucked up into the light socket area when I replaced it. One note of caution, when sticking the tape to the underside of the trunk, don't get it too close to the hole where the existing light facility slides back in, or it could be impacted.I tested the strip prior to install to make sure everything worked (someone noted earlier they had a few of the LEDs not working, in my case everything worked fine).The tape on the LED strip is foam based 3M (at least as labelled) tape. When installed, had good adhesion (unlike traditional LED strips with the paper-think sticky tape). I don't expect this to fail anytime soon.The results were fantastic. As can be seen in the pictures, before and after shots are dramatic (well, maybe that's overkill, but it was pretty cool). This was a great value, and easy project to do. I would recommend to anyone that has a dim trunk light.
Ewbear
Reviewed in the United States on March 25, 2019
This LED strip is an EXCELLENT alternative to the light for your car trunk. There are no instructions, but if you even have novice mechanical skills, you should be able to switch these out. It took less than 10 minutes to install and have light! If you don't have an idea about changing the light out in your trunk, here are some basic steps to assist you:1. Locate where the light source is located in your trunk.2. There may be a clear cover with a tab that will need to be pressed as you pull the cover off. ***Be careful of wires that may be still attached to the cover or light plug as you pull it off.3. Look to see you have the SMD 5050 (plug-in bulb with 2 wire prongs) or the 6418 type (glass tube with cone-shaped metal ends)4. Depending on the type you have, mount your light strip so the center wire connection is within 5 inches of the light plug.5. Connect the appropriate plug type into the LED strip connector, making sure the Red lead and the Black lead are mated the same. (If necessary, use the included lead extension, matching the red and black wires also.)6. When you plug in the connector adapter to the original trunk light plug, the light strip should illuminate.7. Enjoy having sunshine in your trunk!!!I would definitely recommend this upgrade for your trunk!!
Recommended Products
