Your cart is empty.
Your cart is empty.Product Description
Instant Ethernet Network Location
The Cable Matters 1-Port Keystone Jack Wall Plate with Cat 6 RJ45 Insert is the perfect solution for adding a new Ethernet cable location. Disguise the cable to your router or network switch behind the wall for a professional-looking installation. This low-profile wall plate sits almost flush with the wall. Install it easily in the space of a single-gang wall receptacle or add a new location with a low-voltage mounting bracket.
Cost-Effective 2-Pack
This convenient 2-Pack provides enough wall plates for two locations in your home or office.
Standard Single-Gang Outlet
- Convert a single-gang outlet to a network location
- Install a new location with a low-voltage mounting bracket
Cat6 RJ45 Coupler
- Instantly connect an Ethernet Cable
- No wire termination needed
- Provides a neat and tidy installation
Simple Installation
- 2x Wall Plates
- 2x RJ45 Keystone Jacks
- 4x Matching Wall Plate Screws
pierop
Reviewed in the United States on November 6, 2024
Nice wall plate--it worked as advertised.
A-Aron - Customer
Reviewed in the United States on November 10, 2024
I'm really happy with these Ethernet wall plates! They work perfectly, were super easy to install, and seem very well-built. The design is clean, and they’ve made my setup look more organized. Highly recommended for anyone needing a reliable wall plate solution!
JIMI
Reviewed in the United States on October 27, 2024
As described - would buy again.
Danny Penn
Reviewed in the United States on January 11, 2024
I purchased these for a major cat cable install project. No problems at all. Will buy again.
L.W
Reviewed in the United States on March 3, 2022
Great product and very easy to install. My wifi signal was week so I wanted to use an Ethernet cable with my fire cube. Was able to install both ports and hardwire my fire cube in under 30 minutes.
Customer
Reviewed in the United States on March 13, 2021
They're way easier than crimping. However, I ordered a batch of these and found one that allows the signal to drop if the cable is torqued lightly on the inside. If you are willing to purchase more than you need, then I recommend it. Expect that some of them may be DOA.
A. Taylor
Reviewed in the United States on May 30, 2020
These wall panels are perfect in every way. The right price. The right fit. The right connections. I had already prepped the walls for these panels ahead of time, so when they arrived, it was just a matter of connecting the ethernet cables, and screwing them into the drywall. Total time, about 2 minutes. I now have a nice clean ethernet connection from the family room (Where the modem/router is), to my office. No more relying on wifi.There is no speed reduction on these plates. No throttling. No idea what that other reviewer was doing, but he was wrong. I've attached screenshots showing my speedtest results both before and after connecting my system through these wall plates. You can plainly see that the speed did not go down, at all. Heck, through the magic of variability of internet connections, it went UP! (The 857mbps speed was AFTER running through these plates).You cannot go wrong with these.
Mark Peters
Reviewed in the United States on June 12, 2019
I was thrilled to find these available on Amazon since they are hard to find for some reason. I used these for running a hard line from the first floor to the upstairs computer room during a remodel and it was much easier to just buy a 100-ft network cable with pre-installed ends and run it through the open walls and then just plug into the back of these wall plates. Also allowed for easy testing prior to getting everything closed up and the wall plate screwed in.Quality was very good on these and included all hardware needed to install. It was as simple as cutting the hole in the wall, installing the box, running the network cable into the box, plugging the cable into the Cat6 RJ45 insert and screwing the plate into the box. Easy peasy.Highly recommended that you purchase these versus the standard ones where you need to seperate wires and use the tool to press them into the correct slots and hope it all works.
Recommended Products