Your cart is empty.
Your cart is empty.
BIGTREETECH Manta M5P Control board Product Introduction:
BIGTREETECH Manta M5P is a 32-bit motherboard developed by the 3D printing team of Shenzhen Big Tree Technology Co.,Ltd. for Klipper running.It can run Klipper with a core board,which greatly eliminates the mass wiring between the motherboard and Raspberry-Pi ,and also greatly saves space in the chassis.The BTB header sare designed on Manta M5P, so that customers can choose to use CM4 or other solutions, thus solving the insane shortage of Raspberry-Pi CM4.
Main Features
1. 32bit 64MHz ARM Cortex-M0+ series STM32G0B1RET6 MCU.
2. The thermistor circuit is protected to prevent MCU damage from shorted heated bed and heater cartridge connections.
3. The CNC fan's voltage is selectable in 24V, 12V, and 5V, no more need for external stepdown thus preventing board damage from user error.
4. Thermistor connection supports pull-up resistance value setting using jumpers, no more extra module needed for PT1000.
5. MCU firmware can be upgraded via an SD card, or use DFU via Klipper's make flash command.
6. BTB connectors are adopted between the motherboard and core board, allowing the choice of other core board solutions in addition to CM4.
7. Integrated SPI and UART mode of TMC driver and DIAG pin, easily configurable with jumpers.
8. Support filament runout sensor, BLTouch, RGB, etc.
9. Replaceable fuse for easy maintenance.
10. Onboard proximity switch port, support NPN and PNP type selection, (24V, 12V, 5V) voltage selection.
11. Onboard SPI interface for connecting acceleration sensor to enable Klipper's input shaping.
12. The new E-FUSE fuse is equipped, which can respond quickly, enhance self-protection ability, and greatly reduce the motherboard burnout caused by short circuits or ignition.
J
Reviewed in the United States on June 3, 2024
This is probably the most frustrating control board I've ever used. The Raspberry Pi that comes with this was DOA. No matter how many times I flashed an image to the SD card, it just wouldnt boot. Just a solid red light. I would then move that same SD card to a real raspberry pi 4 and it would boot just fine. Given this, I decided to forgo the klipper route and try just flashing with Marlin to get the printer running in the meantime, and after days, I have not been successful. My biggest issue at this point seems to be getting an LCD to work. Tried setting it up with a RepRap Discount Full Graphic smart controller I had lying around and was able to get the graphics to work, and clicking the encoder button worked, but the minute I tried to turn the encoder, the controller would reset itself. Spent hours going over the pinouts from the screen to the pinout in the config pins file, and then back to where they are defined and all appear to be correct, but no dice. So I decided to then try a MKS TS35 V2.0 screen I had laying around and it was even worse. I cant even get an image to show up on the screen.Then we move onto the power issues. I gave up on the screen and was trying to connect to the board via serial usb. The connection was inconsistent at best, and when I was able to get it to connect, none of the motors will work, despite having the stepper motor power posts connected to the PSU. In fact, the only thing I have managed to get to work at all using this board is heating up the hotend. Thats it.At this point im done with this board. If I could give zero stars I would, and if i still had the boxes this crap came in it would be on its way back.
Customer
Reviewed in the United States on January 2, 2024
I now destroyed two npn no prox switches trying to make them work as a z probe on a 5 volt rail. The docs are a bit confusing. Other than that, a great product, I have used several of both of the boards in bigger printers. For a rebuild or a new design, these are do it all boards
Chip
Reviewed in the United States on August 7, 2023
I was able to get this into my 3d printer after several hours of research. I recommend this board but be prepared to learn.
KM
Reviewed in Germany on August 30, 2023
Vorsicht! Hier gehtes nicht um das Mainbord sondern um TMC2240 Treiber. Dachte durch die vielen Bilder dass es sich hier um eine Platine für den Drucker handelt. Der Verkäufer sollte richtige Bilder nehmen zu seinen Produkten. Klar ich hätte auch lesen können.
Mark Blalock
Reviewed in the United States on May 3, 2023
These boards suck! 3 different octopus pro boards and all bad. The spi is bad on all three, one the usb is bad and one restarts by itself. Amazon won’t let you return something twice so I am out quite a bit and no working board! There has to be something better!
Kai Jensen
Reviewed in the United States on February 16, 2023
That's the best controller board so far. The first one was partly dead because the USB-C port was dead, but Jeff replaced it no questions asked.Great service Jeff, keep it up.
Dave
Reviewed in the United States on August 7, 2022
I bought this board to build a custom 3d printer. I'd researched for weeks on the "best" replacement boards and this one was always at the top of the list. It was delivered as promised, in beautiful packaging, with ZERO instructions. None. There's a piece of paper that says to go to their GitHub, Discord or F**ebook page. What if I don't use Discord or Facebook? Well, despite this board having dozens of options, hundreds of connectors, jumpers and headers, the "user manual" is 8 pages of useless information. Both the GitHub location and the "user manual" indicate that some drawings (very important power-related jumper settings) might be wrong. I had questions, so I tried the Discord - no answers. I tried multiple emails - no replies. After complete frustration set in, I tried Facebook. I was berated and bullied by several members (including an admin) for asking questions too "aggressively". Still no answers, though. Not a one. TLDR; buy this product ONLY if you have 100% confidence that you know how to configure and connect it because there will be no help from the people that make it. BTT has already warned me that they're going to bully and shame me some more, using my Facebook posts, if I posted an honest review. So, that's who you'd be dealing with if you need help with this or any other BigTreeTech product. They'll never get another dime from me and whoever's reading this should reconsider, as well.
Rich
Reviewed in the United States on August 29, 2022
Tends to overheat in a hot garage without excessive cooling (read: 1000cfm room fan). I have had several fail in different ways. Tend to blow out individual circuits rather than kill the whole board, but often there is only one built in redundancy before you render the board useless (looking at you, heater circuits).
Zbad
Reviewed in the United States on April 27, 2022
Are you serious enough about 3d printing that you wanna bump the game up to life threatening stepper voltages? Then this is your huckleberry because you can. Wanna dabble in 5 axis printing? Why not. Do it.
Recommended Products
