Your cart is empty.
Your cart is empty.Product Description
Product Sizes
- Type:M3*0.5/M4*0.7/M5*0.8/M6*1.0/M8*1.25/M10*1.5/ M12*1.75 HSS
- Thread Diameter:3/4/5/6/8/10/12mm, Total Length:51/56/61/70/72/76/86mm
- Square Head Size:(L*W):2.5x2.5/3.1x3.1/4.0x4.0/5.0x5.0/5.0x5.0/6.3x6.3/7.0x7.0mm
- Shank Diameter:3.0/4.0/5.1/6.0/6.3/8.0/9.0mm,Pitch:0.5/0.7/0.8/1.0/1.25/1.5/1.75mm
- Pitch:0.5/0.7/0.8/1.0/1.25/1.5/1.75mm
Hightlights
Material :High Speed Steel
Thread Direction: Left hand
Package Included: 7x Left hand Thread Tap
Marvin L.
Reviewed in the United States on September 1, 2024
Nice assortment of metric left handed taps. Of course you can always use your right hand, 😂 but these are for left handed threads. I work on equipment, and lots of times, they tighten by turning counterclockwise, so this is when these really come in handy, for cleaning up damaged threads. I hope you didn’t mind the little humor, but we all need a bit from time to time. Oh speaking of a bit. They also make left handed drill bits. 🤷♂️
Thomas Lalle
Reviewed in the United States on June 28, 2024
need to tap a bushing with left handed threads, i intended to use on an electric motor... to eliminate the gap on a factory threaded axel. the ta; snapped off while trying to tap the bushing.... should not have been a difficult job for the tap.
ENPOS E.
Reviewed in Spain on December 4, 2024
NO SIRVEN PARA NADA, NO LO RECOMIENDO
dieter georgi
Reviewed in Germany on October 30, 2024
diy-qualität
Jack
Reviewed in the United States on January 28, 2024
Had to tap mirror holes on my Victory Judge to put plugs in. Reverse thread just to make it more fun to find tool to work. Tap worked great with Gearwrench set.
William Cochran
Reviewed in the United States on January 14, 2024
Came on time and work great
Vincent Gonnet
Reviewed in France on August 3, 2023
Les taraudages à gauche sont assez rares en mécanique, on les trouve plus fréquemment sur du matériel de jardinage, débroussailleuse et autre. Et faute de taraud, on est bien embêté pour réparer !
ifishtoo
Reviewed in the United States on August 20, 2023
I used one tap to turn a 10 mm bolt head into a 10 mm left hand nut. Some of these cheap tops are not hard enough cut virgin threads but these ones did the job just fine mine is not a production environment so I can't tell you how many threads you'll be able to cut before they go dull. If they do they're fairly simple to sharpen.
Roger Heimpel
Reviewed in Canada on October 22, 2023
I bought this LH metric tap set to retap a crankcase that had the primary clutch bolt snapped inside. Bombardier outlander 400. After drilling through the snapped bolt, the M12x1.75 tap worked great, using motor oil and using 1/8 turns and then backing off. Very pleased and arrived quickly.
CF
Reviewed in Italy on April 6, 2022
Arrivato orima del previsto
Rich11
Reviewed in the United States on September 23, 2021
They worked for what I needed them for. Cleaned out the threads on my miter saw.
Lars
Reviewed in the United States on July 9, 2021
Worked good, nice little set of taps. Didn't come oiled or anything but weren't rusty either, I just tapped cast metal on the softer side so I don't know how they perform on harder metals but they came sharp and clean.
Zane
Reviewed in the United States on February 17, 2019
It's hard to find a source for left hand metric taps. I'm glad I found these. I've used them on brass and steel. So far they cut very well. I cut brass dry and steel with sulfated pipe cutting oil
Recommended Products