Your cart is empty.
Your cart is empty.Garry_James
Reviewed in the United States on September 10, 2024
I have the Aqua-Rite Goldline salt system. The thermistors burn out every 2-3 years. Just spending about 1/2 hour desoldering the old and soldering in the new thermistor has saved me thousands of $$$.
Brian Childers
Reviewed in the United States on August 26, 2024
this self-repair saved me hundreds of dollars
Bike Rider
Reviewed in the United States on July 31, 2024
Fixing the Thermistor was pretty straightforward. This part was an exact match to the failed part and worked perfectly.
brad
Reviewed in the United States on June 17, 2024
It's hard to capture my Aquarite GLX-PCB-RITE circuit board symptoms, but essentially they were sporadic. Lights would turn on, then turn off, and occasionally turn back on again and off. Sometimes this would be triggered by switching from Super Chlorinate to Auto, sometimes not. It was frustrating. The GLX-PCB-DSP (display) never seemed right, either, in that it wouldn't read salt levels or try to calibrate to salt levels. Basically I was getting funky readings, though other settings on the display seemed normal. I did try to replace the display with a knock-off brand - didn't resolve. I tried a knock-off control board, too - it didn't resolve the issue, though logically, it should have. Maybe a bad board or connection somewhere(?) It was set to the correct cell type, but oh well, returned both for refunds.So I bought this Thermistor (x2) as I've run across a lot of similar symptoms to my issue online. Also bought a $20 solder kit. Never soldered before, and it probably took me longer than it should have to remove the old Thermistor, but it wasn't a difficult swap and got this guy soldered in after a few minutes. Connected the old circuit board back up and it worked beautifully! Had to change the cell settings but otherwise it was great. Lights are working and not cutting out like before. It read and allowed me to set my salt levels. No issues so far! Extremely pleased.
Jeffrey Brant
Reviewed in the United States on May 20, 2024
This part commonly burns out after 2-3 years in most chlorine generators. Of course the local pool company doesn't tell you how easy this is to fix yourself at a very affordable cost if you have experience with electronic soldering and are comfortable working with electronics. Instead, they want to sell you a replacement circuit board for around $400.This is the third time in about ten years I've had to replace the thermistor. The circuit board is easily removed (be sure to turn off the circuit breakers to the controller first!). You can simply solder out the old thermistor and solder the new one in. Replace the circuit board and turn back on the circuit breaks. You should be good to go. It is nice having the two-pack so I will have a spare ready the next time it burns out (in about two to three years).
Beeblebrox
Reviewed in the United States on December 8, 2024
These thermistors last about 3 years inside an Aqua-Rite chlorine generator due to a poor printed circuit board design that has insufficient heat-sinking, causing the thermistors to run very hot. So I always keep a supply of these thermistors on hand for the day when the Aqua-Rite system starts acting squirrely (sawtooth voltage pattern with about a 1-minute cycle).
Michael Todd
Reviewed in the United States on July 27, 2023
Aqua-Rite Thermistor AS32 2R025.( Pack of 2) Inrush Current Limiter 2 Ohm Ohm ±25% 1.18" (30mm) wrong one for me
Curtis
Reviewed in the United States on August 5, 2022
My pool guy was going to charge $300 to replace the circuit card on my chlorinator control box. The circuit card is $150 and an easy 5 minute swap that anyone can do. If you can solder, or knows someone who can do it for you, then it will cost you $13 and 15 minutes, plus you have a spare for next time. I have replaced this same part 3 times in the last 16 years so it does last and is a lot better than replacing the card 3 times. The replacements have lasted just as long as the original which is about 5 years. This is the only part that has failed on my control panel to date...knock on wood.
Melanie
Reviewed in Canada on March 13, 2021
Utiliser pour réparer une soudeuse .
Fred Labbate
Reviewed in Canada on August 7, 2020
Great did the job
Recommended Products
