Your cart is empty.
Your cart is empty.Product Description
- Fully potted 6ohm resistance, for 9005/9006, H7,H11,H13: resistor-based CANBUS error decoder, also fix flickering
- High quality, engineered to last and be the safest way to add load equalizer to automotive lighting system: 3x more Surface Area for heat dissipation than traditional golden resistor
- The most thermally safe resistors on the market: Max. operating temperature about 200° F when properly mounted to metal surface, up to 100° F less than traditional golden resistor
- Super long reach: 36" cable measuring from bulb to resistor allowing resistor being mounted to a perfect metal flat spot (29.5" cable from resistor, 5.5" from male and female harness)
- Lower profile, about 1/3 flatter than traditionally golden resistor, greatly reduces the chance of touching any plastic parts Weather tight and sealed connectors between resistor and harness, weatherproof and
- DIY friendly, plug and play choices to either connector resistors to both high and low intensity for 3157 and 7443, or only to connector resistor to high intensity and to leave low intensity connector empty wrapped with electrical tape which is the case for most vehicles
- Current Draw: 2A @ 12V | 2.4A @ 14.4V. Each piece of resistor will add Load = 1 standard incandescent bulb (equivalent wattage: 24W)
- Dimension: 3.44"x1.53"x0.47"
Applications
- Fix LED flickering issue
- Stop Hyper Flashing
- Remove error code by BOC
- Cancel radio interference
- Plug-n-play, long wiring for the best easy installation
Tyler C. Wright
Reviewed in the United States on February 10, 2025
Product never worked for me still flickering lights.
Antony García
Reviewed in the United States on September 17, 2024
Muy bueno
Christian Luc Tremblay
Reviewed in Canada on December 31, 2024
parfait
MTB rider
Reviewed in the United States on June 14, 2023
Lucky break with being able to use existing car design to easily incorporate the resistor. I had concerns about mounting the resistor. In the pic you can see where an existing hole allowed me to use a screw with washer and then the resistor fit under the metal piece that holds the headlight to frame. Had to make one hole on back of light housing to run wire out. Extra length in wire is the secret.
Vicente el Español
Reviewed in the United States on May 18, 2023
Product absolutely does not work. I bought Sealight H 11 LED bulbs for my 2010 Toyota Camry hybrid, but these bulbs kept flickering when you turned on the day running lights. Only in complete darkness, so when it had become completely dark, the LED lamps no longer flickered. Amazon.com recommended that I buy the Alla lighting decoder and they guaranteed that there would be no more flickering after connecting the decoder. I had the decoder connected professionally in a car garage, but after connecting the decoder instead of the H 11 LED lamps, the H 3 LED lamps (high beam) started to flicker when switching on the day running light mode. Either my Toyota Camry is not suitable for LED lighting or the Alla lighting decoder is just a worthless product that does not deliver what it promises to do.
Jonathon O.
Reviewed in the United States on January 10, 2023
This product simplified my previous wiring with one harness; on my Audi's fog lamps converting to LED bulbs required a separate CANBUS decoder and 6 ohms resistor. The length of wire from the plug to the decoder/ resistor allowed me to consider more mounting locations and to mount on a larger piece of metal to help dissipate heat. The size of the decoder/ resistor made it a little more of a challenge, but the performance so far has been very good (used it for the last couple weeks without a fault code tripping).
Murat
Reviewed in the United States on September 30, 2022
Work well, but lights are not so bright, i don't know that about lights or not I am not sure , but it's working,.
kyle
Reviewed in Canada on February 6, 2022
Used this product briefly. It didn't prevent flickering and it got so hot it melted the velcro patches I used to attach it. Also burned my fingers when I touched it. Save your money.
Oswaldo Sanchez
Reviewed in the United States on October 13, 2022
I had to cut the wires from the harness to hard wire as the harness didn't fit existing OEM. After a week lights started hyper flashing.
Joshua Maddox
Reviewed in the United States on April 27, 2022
This is the 4th decoder I have tried on my 2006 Volvo S40 and the only one that has worked so far. It does seem better made than the others I have tried, and I no longer have a bulb error on my dash.
Recommended Products