Your cart is empty.
Your cart is empty.Product Description
2GT TIMING BELT
- Looks Great, Works Great, Perfect Grip
- Maintains a Consistent Width
- Moves Very Smoothly
1. Neoprene Tape Back
Prevent damage caused by friction, excellent hydrolysis resistance and heat resistance.
2. Glass Fiber Anti-Position Layer
High strength, low elongation, good corrosion resistance, good heat resistance.
3. Neoprene Tape Teeth
Correctly engaged with the tooth groove of the gear.
4. Nylon Cloth Layer
Better protection of the tooth joint and extended service life.
The Inspector
Reviewed in the United States on January 8, 2025
I recently bought my first CNC router and have been pulling my hair out (and I don't have much to begin with, so that in itself is problematic) with the OEM belts skipping steps. I tried tightening. I tried loosening. I just couldn't turn my back on again project for fear of them skipping and screwing up the project.SO.... I found this belt and liked the description indicating that it likely had a better gripping surface, so I gave it a try.And boy am I glad! Deeper cuts at faster speeds and not even an inkling of slippage!Don't tighten it too much though. The tensile strength isn't great. Hopefully that doesn't become an issue down the line. If it does, I'll update my review, but as for now, I'm really happy I found this!
Thomas Kircher
Reviewed in the United States on January 8, 2025
This isn't genuine Gates GT2 belt, it's a cheap Chinese knockoff. But it works fine. It will likely wear out faster since it doesn't contain any fiber reinforcement. It also smells pretty strongly of rubber.
albert ruiz
Reviewed in the United States on January 20, 2025
Good fit i bougt this belt to replace the ones on my cnc laser cutter goodquality very strong
Damir
Reviewed in Canada on July 14, 2024
Black belt for comparison, brow in the one I got.You can easily see that teeth are inconsistent and there is no fiber reinforcement.So I wouldn't recommend to buy it
Miguel Angel de Jesus
Reviewed in Mexico on June 12, 2024
Llego mucho antes y se ve muy resistente la correa la ocupe para una Ender 3 S1 pro,como viene en rollito solo la corte a la.medida de.la.orig8nal y listo trabaja perfectamente y sobra para furas reparaciones, se ve mejor que la original que traia la impresora.
karl
Reviewed in the United Kingdom on December 24, 2024
Ok
pgolos
Reviewed in the United States on December 15, 2024
Nice 3D printer belt; it is very high quality, like a car timing belt; it has many layers and is very strong. exactly what you need for a fast 3D printer.
Mr1
Reviewed in Sweden on November 27, 2024
Belt seems to be off good quality, but realized it's far less than 5 meters
Customer Review
Reviewed in the United States on October 30, 2024
I needed two sections of about 2 meters in length of this GT2 timing belt for my Zero G Mercury One custom CoreXY 3D printer build.Unlike other rubber GT2 belts, this one has fiber reinforcement and resists stretching - very similar to the original Gates product.The tooth profile of this belt is identical to Gates and meshes with my toothed idlers perfectly. In the year of constant 3D printing with this belt, I have seen no belt degradation of any sort (no fraying and no cracking).CoreXY builds are especially taxing on timing belts because of their forces, and back and forth bending of the belt as it runs through the pulleys. I run this 3D printer very hard and have had no problems whatsoever. I would buy this belt again - no complaints!
Alessandro
Reviewed in Italy on October 12, 2024
Non hanno fatto troppe ore per adesso,ma si comportano bene, consigliate
Dr. Ejmo
Reviewed in the United States on July 22, 2023
These worked just fine on my generic gantry printer. After reading other reviews re: width, tooth spacing etc. I measured the width of the coiled belt by taking several radial readings with calipers and got 5.88mm to 5.94mm readings, consistent with the values posted by others. Under magnification, the tooth spacing seemed fine.In use, the belts work just fine. My printer is 3 years old and I was noticing that the teeth on the original belts seemed worn. Sure enough. I installed the the new ones as part of a general maintenance, cleaning, tightening, new nozzle, and (meshed) bed leveling, etc. My prints are better than ever due at least in part to the belts. As the originals wore, the layers became uneven due to in part belt slop. These take more tension so slop is greatly reduced.I'd buy these again.
Gary V
Reviewed in the United States on October 13, 2023
If you own a ender 3 series print, you know this timing belt will break or stretch. I recently upgraded my ender v2 to an extender. The problem is finding a belt for this upgrade. The printing bed is very large . Needing a long belt I found this belt. The belt is reinforced. This eliminates the stretching problem. With the length of the belt, I can upgrade several prints. Great belt for the price.
William Polansky @a6uh
Reviewed in the United States on April 1, 2022
I've bought and returned 3 other belts here trying to find one that was *actually* 6mm in width. All the ones I tried would vary between 5.8mm - 6.1mm and on some printers that would still work. However, most printers use a 6mm idler/ bearing, so all the spots where the belt is wider than 6mm it rides up against the flange or over the bearing. That causes a loud crinkling noise and leaves artifacts in your prints. I was beyond frustrated getting poor quality belts with awful tolerances that claim to be "precision belts".Now these belts, are great. I saw a review saying not to even bother with the other belts here on Amazon and they are so right. These belts varied from 5.86mm - 5.94mm, so they actually work great, fit, are quiet, and don't leave artifacts.If you need a 6mm belt and don't want to spend 4x the price for Gates belts, buy these. Seriously. I can't recommend them enough.
Recommended Products