Your cart is empty.
Your cart is empty. M6 Rivet Nuts Stainless Steel Threaded Insert Nutsert Rivnuts Flate Head
A Rivet Nut fastener is a tubular rivet with internal thread which can be installed in seconds form one side of the work. Once installed, no finishing work is required on the RIVNUT fastener.
The added benefit of not only being a dependable fastener, they are ready to use with clean threads available for screw attachments.
Rivet Nuts also are used when an application has little or no access to the backside as they can be installed from the front side of the work piece.
Package Quantity: 40pcs M6 Stainless Steel Rivet Nuts Threaded Inserts
Barry
Reviewed in the United States on September 9, 2024
Used this product to mount furring strips to a cargo van using a RivNut tool. The rivet nuts have been holding strong and had zero failed rivets in the entire bag I used. It is important to drill out the holes to the correct sizes for the rivet nuts to take.
michael stevens
Reviewed in the United States on September 16, 2024
I will be ordering from this company again
Stephen D. Wall
Reviewed in the United States on August 26, 2024
It’’s extremely important to use these correctly. A high-pressure grease MUST be applied both to the tool and the part. Otherwise, damage will occur. Setting pressure should be moderate to high. Epoxy should be mixed and applied to both part and substrate. I had excellent results. It’s less important but worth noting that dissimilar materials interact in ways that might destroy both, so please consider NoAlox instead of epoxy.
T. Shoup
Reviewed in the United States on August 26, 2024
I had a stripped M8 threaded hole in a piece of cast iron, the wedge nut on a bicycle handlebar quill stem. I bored out the hole to the 11mm required by these nut inserts and then using just a 5/16" threaded rod (it's a hair less than 8mm diameter) and 2 nuts I was able to squeeze this insert sufficiently and lock it into the cast iron piece. I was able to reassemble the bike stem and handlebar and tighten things down sufficiently. This was far easier than anything else I'd tried earlier.
T.S.
Reviewed in the United States on August 1, 2024
fit great
BGF
Reviewed in the United States on July 20, 2024
I was afraid that being stainless steel that these rivet nuts would be difficult to expand; they were not. They worked perfectly. I like the they are sold in smaller quantities, I needed about 20 and glad I don’t have a ton extra sitting around and probably never use. All were perfectly formed and threaded. I recommend and would buy again if ever needed.
Steve R.
Reviewed in Australia on July 12, 2024
Bought these Rivets to fix an issue with existing blind nuts on my boat, I didn't use the rivet process but used them as blind nuts inserted from below the fibreglass hatches to re attach the hinges. worked perfectly in this scenario and have repaired other issues on others boats.
Dave R W & Peggy M
Reviewed in Canada on December 30, 2024
Used for installing center console in my Ranger, will be using for a bunch more stuff later. Seem to be good quality, no installation dramas with the right tool.
Bill
Reviewed in Canada on December 28, 2024
These are quality and functioned perfectly. Easy to install with the right tool.
azapplewhite
Reviewed in the United States on October 29, 2024
Good value - decent quality
bayne1
Reviewed in the United Kingdom on April 30, 2024
good quality value for the money
David Ussell
Reviewed in the United States on October 22, 2023
. . . but that's because stainless steel is not supposed to be magnetic. Stainless steel is not steel per se. It is a very mildly ferrous material. It's unfortunate that they have slammed the product just because they don't know that they are talking about. Besides in the ad copy it correctly indicates the material is austenitic stainless steel and neither magnetic nor aluminum.The parts are well made, and work well. They are good value for the money. Although I have an appropriate tool for inserting these I'm not likely to use it except for setting it up for big runs. Instead, I'll use the nut and bolt method with my torque wrench. This will allow me to precisely set them making them tight without stripping them.If I need to install a lot I take the time to adjust my setting tool correctly on a scrap piece of metal. Without doing that it is easy to strip threads.
ALAIN SEGUINEL
Reviewed in France on July 23, 2021
Bon produit
Recommended Products
