Your cart is empty.
Your cart is empty.Product Description
2M Temperature Measuring Line, K Type Temperature Sensing Line
2M Temperature Measuring Line, K Type Temperature Sensing Line, Thermocouple Temperature Probe, Sensor TES1310 TM902C
Fiberglass material
Glass fiber is an inorganic non-metallic material with excellent performance, good insulation, strong heat resistance, good corrosion resistance and high mechanical strength.
Standard small yellow flat plug
Suitable for K-type instruments such as 902C, 1310, 6801A, 6802A
Exposed temperature measuring point
Solder joints are round, plump and bright
Can measure the temperature of liquid, gas, air, concrete
Michael Paliotta
Reviewed in the United States on November 21, 2024
A little flimsy however nice and long and priced right. They work fine otherwise.
Michael Paliotta
Reviewed in the United States on November 21, 2024
A little flimsy however nice and long and priced right. They work fine otherwise.
Tim Walker
Reviewed in the United States on December 30, 2023
The connectors are two thick to fit down in my field piece. Had to sand them down some to get them to fit. They read temps correctly on my meter. I've used 2 of 5 and they have held up to being tossed around in a tool bag for 2 months. Not for high temps. Insulation with burn off. I've used them to verify oven chamber temp up to 400f seems fine, do not use on an open flame. Price is reasonable.
Tim Walker
Reviewed in the United States on December 30, 2023
The connectors are two thick to fit down in my field piece. Had to sand them down some to get them to fit. They read temps correctly on my meter. I've used 2 of 5 and they have held up to being tossed around in a tool bag for 2 months. Not for high temps. Insulation with burn off. I've used them to verify oven chamber temp up to 400f seems fine, do not use on an open flame. Price is reasonable.
Jeff Goudie
Reviewed in the United States on November 29, 2023
These thermocouples were received by the promised delivery date. They worked very well and I did not have any issues with them.
Jeff Goudie
Reviewed in the United States on November 29, 2023
These thermocouples were received by the promised delivery date. They worked very well and I did not have any issues with them.
John G.
Reviewed in the United States on August 4, 2022
They came packaged well and prompt shipping.They work with my meter just fine. I use these to check incoming and outgoing air temps on AC units home , automotive, and heavy equipment.
John G.
Reviewed in the United States on August 4, 2022
They came packaged well and prompt shipping.They work with my meter just fine. I use these to check incoming and outgoing air temps on AC units home , automotive, and heavy equipment.
Midget Impinger
Reviewed in the United States on February 9, 2021
I ordered this thinking it was my thermocouple that was broken, but when using these gave the same readings, it was evident that I was wrong. I worked with the seller to send them back, and they worked with me on it even though it was entirely my mistake.Great seller! Will work with again in the future, for sure.
Midget Impinger
Reviewed in the United States on February 9, 2021
I ordered this thinking it was my thermocouple that was broken, but when using these gave the same readings, it was evident that I was wrong. I worked with the seller to send them back, and they worked with me on it even though it was entirely my mistake.Great seller! Will work with again in the future, for sure.
Jonathan Huft
Reviewed in the United States on April 9, 2021
Calibrated 10 of these in boiling and ice water.All seemed to be within a degree of correct temperature.Good enough for my purposes.A couple have weld beads that look slightly crusty and might be a bit more prone to breaking than they ought to be.All in all, a pretty good value.
Jonathan Huft
Reviewed in the United States on April 9, 2021
Calibrated 10 of these in boiling and ice water.All seemed to be within a degree of correct temperature.Good enough for my purposes.A couple have weld beads that look slightly crusty and might be a bit more prone to breaking than they ought to be.All in all, a pretty good value.
Rene 1
Reviewed in the United States on February 17, 2020
I'm unable to rate thoroughly because I've only used one out of the five thermocouples. I'm happy with the one I used but cannot of course, rate its accuracy since I do not have a calibrated instrument to compare it to. I used it to check if it works by placing it in the oven while my wife was baking at 375 deg F according to the digital readout on the oven's temperature control. While the temperature on the oven's console was set at 375, the temperature on my Fluke using this thermocouple varied from 370 to 380, definitely within range. At times, it read as high as 400 deg F and that was when the heating coil went on to raise the temp after the oven allows it to cool down to around 360. I was happy to find out that heating coil no longer goes on when there is about 4.5 minutes left on the timer. Cooking will continue using residual heat and just float down till the timer goes to zero. Nice energy saver feature.
Rene 1
Reviewed in the United States on February 17, 2020
I'm unable to rate thoroughly because I've only used one out of the five thermocouples. I'm happy with the one I used but cannot of course, rate its accuracy since I do not have a calibrated instrument to compare it to. I used it to check if it works by placing it in the oven while my wife was baking at 375 deg F according to the digital readout on the oven's temperature control. While the temperature on the oven's console was set at 375, the temperature on my Fluke using this thermocouple varied from 370 to 380, definitely within range. At times, it read as high as 400 deg F and that was when the heating coil went on to raise the temp after the oven allows it to cool down to around 360. I was happy to find out that heating coil no longer goes on when there is about 4.5 minutes left on the timer. Cooking will continue using residual heat and just float down till the timer goes to zero. Nice energy saver feature.
John
Reviewed in the United States on August 12, 2019
It can be used to replace the k-thermocouple that comes with the Rex C100 PID controller, if the connector is disassembled (all screws). My application required a longer k-thermocouple than what came with the controller. I decided to take the gamble, as they are sold 5 to a package, Checked the accuracy as modified and it did not seem to alter it. I will set the upper limit of the controller 1-2 degrees lower until I can establish that it will maintain temps as modified.
John
Reviewed in the United States on August 12, 2019
It can be used to replace the k-thermocouple that comes with the Rex C100 PID controller, if the connector is disassembled (all screws). My application required a longer k-thermocouple than what came with the controller. I decided to take the gamble, as they are sold 5 to a package, Checked the accuracy as modified and it did not seem to alter it. I will set the upper limit of the controller 1-2 degrees lower until I can establish that it will maintain temps as modified.
Recommended Products