Your cart is empty.
Your cart is empty.Product Description
Customized Suitcase
Professional custom plastic carrying case, each accessory has a special slot, easy to carry and store, also can extend the life of the tool.
Puller With Three Grips
Inner hole puller with three grips not only can bearings be easily removed, but flywheels and gears can also be removed with the three-jaw puller.
Collet Size Model
Our bearing puller set comes with 6 different types of red steel collets for non-destructive removal of a wide range of bearing sizes.
Ragnvald B.
Reviewed in the United States on February 28, 2025
Good tool of last resort!
tnt0031
Reviewed in the United States on January 11, 2025
Works as described
Customer
Reviewed in the United States on September 22, 2024
worked very well with lots of options for different applications
Bill or Sparkey
Reviewed in the United States on August 14, 2024
This puller has a wide range of collet fingers that inserts into the ball bearing grove of the inner and outer bearing races. However, it's limited to a particular series of bearing sizes as shown in the 1st and 2nd pics. The collet puller feature ONLY works on bearing that ARE NOT sealed, unless you removed the sealed from the bearing and replace it with a new bearing. The collet puller WILL NOT work on taper roller bearings.Therefore, this puller will get a 4 rating for that feature.You do have fingers that can be use to pull a bearing as an alternate way. 2 or 3 finger method, however pulling any pilot type bearing will be difficult due to the fingers thickness. Pic 3, Reason I give it 3 for that.Setting up the puller can be intimidating or complete frustration for a beginner DIY. This is due to aligning on keeping things in place while tightening the nuts before you pull the bearing. That could be a 2 rating.As far as the Heavy Duty Case, it ain't in my opinion. My set got rough up during shipment. Most of the parts were out of their restraints and some will not lock in and stay in. There should be some type of heavy foam or something, that keeps the individual parts in place. Rather disappointing to say the least.This puller set does have a lot of 5 rating features, but lacks in certain areas too.I'm going to be neutral on any recommendation as yes or no on this product. I will let the readers decide.
The traveling mechanic.
Reviewed in the United States on August 11, 2024
I used this the other day on a haybine. It worked like a charm. The only complaint I have is the cheap blow molded case. Some of the attachments fall out every time you open it. I would have gladly paid more money for a good case. Product is tough & does what it's meant to do.
Abner Petersheim
Reviewed in the United States on July 25, 2024
I loved the performance of this bearing puller set. I pulled 2 bearing off of a shaft that had no room for a regular gear puller jaw. An absolute life saver!! This set is a must have for anyone who needs to pull off even 1 bearing let alone a lot of them.
K. Zimmer
Reviewed in the United States on December 6, 2024
Lasted for 2 bearings. And didn't finish taking the last bearing out. The pusher bolt stripped out the handle
Matthew K. Wimmer
Reviewed in the United States on December 20, 2024
This worked to remove the badly stuck blind bearings in my mid-90s Class tedder angle drives, when nothing else could. I was able to remove one of the stuck bearings by inserting an air hammer through the filler port of the gear box and driving it off at an angle, but none of the other ones would move and an external puller couldn't grab them. I punished my pride for nearly a week trying get those 5 remaining bearings out and eventually gave in and purchased this internal race puller. Should have done it sooner. The wedge/hooks in this kit are indredibly hard and strong and bit into the races after destroying the sheilds and cage as instructed. All 5 rusty, stuck, blind bearings came out with minimal fuss. I lent the puller to a friend for work on a tractor transmission and he too commented on it's effectiveness and utility. A great tool when no other type of puller will work, and this seems to be a pretty well made example to boot!
Recommended Products