Your cart is empty.
Your cart is empty.iMetrx Nema 17 Stepper Motor 42x38mm 17HS4401 1.5A-3.8V 2 phase 4 wires 1.8 degrees with 1Meter cable for 3D Printer Motors
Adrian J.
Reviewed in the United States on February 6, 2025
worked great on my voron trident build. NO problems at all
Adrian J.
Reviewed in the United States on February 6, 2025
worked great on my voron trident build. NO problems at all
Verry poor quality
Reviewed in Belgium on February 21, 2025
dont buy this for a creality 3d printer
Verry poor quality
Reviewed in Belgium on February 21, 2025
dont buy this for a creality 3d printer
HarryJ
Reviewed in the United Kingdom on January 8, 2025
Bought these to use with a 4:1 pulley for some moderately heavy Venetian blinds. Only gripe is that without idle hold enabled, then still turn when under load.
HarryJ
Reviewed in the United Kingdom on January 8, 2025
Bought these to use with a 4:1 pulley for some moderately heavy Venetian blinds. Only gripe is that without idle hold enabled, then still turn when under load.
Cleaver Greene
Reviewed in the United States on January 7, 2025
Nothing wrong with these motors. But one would wish the sellers could precisely state the pin connections of the connector as well as the phase/winding resistance. So for the record: These motors have the 'crossover' 1-3 and 4-6 phase connections. The phase resistance is 2.3 Ohms as measured with a regular digital multimeter. What would we do without free returns!...;-)
Cleaver Greene
Reviewed in the United States on January 7, 2025
Nothing wrong with these motors. But one would wish the sellers could precisely state the pin connections of the connector as well as the phase/winding resistance. So for the record: These motors have the 'crossover' 1-3 and 4-6 phase connections. The phase resistance is 2.3 Ohms as measured with a regular digital multimeter. What would we do without free returns!...;-)
Landon Brown
Reviewed in the United States on July 13, 2024
I'm currenrly using this motor to drive my secondary z axis upgrade and have had zero slips. The actual motor is nice and small, but has the perfect shaft size for just about any 3d printing use.
Landon Brown
Reviewed in the United States on July 13, 2024
I'm currenrly using this motor to drive my secondary z axis upgrade and have had zero slips. The actual motor is nice and small, but has the perfect shaft size for just about any 3d printing use.
Tj
Reviewed in the United States on June 22, 2024
exactly as described
Tj
Reviewed in the United States on June 22, 2024
exactly as described
Silly Snek
Reviewed in the United States on March 21, 2024
Finally installed these months after ordering as back ups. 2 of the motors couldn't keep up with prints without skipping and slipping. Swapped them around and same 2 did same behavior. Had one on the direct drive and it would push fine until quicker extrusion then would skip and pop back on itself resulting in trash prints. Way too late to return but definitely not worth 2 of the 3 ordered. So far the 3rd is working fine so possible fluke or ticking time bomb of failure.
Silly Snek
Reviewed in the United States on March 21, 2024
Finally installed these months after ordering as back ups. 2 of the motors couldn't keep up with prints without skipping and slipping. Swapped them around and same 2 did same behavior. Had one on the direct drive and it would push fine until quicker extrusion then would skip and pop back on itself resulting in trash prints. Way too late to return but definitely not worth 2 of the 3 ordered. So far the 3rd is working fine so possible fluke or ticking time bomb of failure.
GROGNON
Reviewed in France on December 10, 2024
Pris pour le remplacement du moteur de l'extrudeur de ma FLSUN SR.Aucun problème mécanique pour le remplacement.Ne pas essayer d'utiliser le câble d'origine, il faut utiliser le câble qui est livré avec le moteur.PAS DE DOC,
GROGNON
Reviewed in France on December 10, 2024
Pris pour le remplacement du moteur de l'extrudeur de ma FLSUN SR.Aucun problème mécanique pour le remplacement.Ne pas essayer d'utiliser le câble d'origine, il faut utiliser le câble qui est livré avec le moteur.PAS DE DOC,
Gimenez André
Reviewed in France on November 27, 2024
Moteur pas a pas pour ma cr10 s5 remplace l ancien qui avait un aimant fendu
Gimenez André
Reviewed in France on November 27, 2024
Moteur pas a pas pour ma cr10 s5 remplace l ancien qui avait un aimant fendu
Timothy A Stiel
Reviewed in the United States on October 27, 2024
Great Ender motor replacements seem well built. Will see if these last longer than the original motor.
Timothy A Stiel
Reviewed in the United States on October 27, 2024
Great Ender motor replacements seem well built. Will see if these last longer than the original motor.
kh
Reviewed in Germany on October 20, 2024
Hat die Erwartungen erfüllt !
kh
Reviewed in Germany on October 20, 2024
Hat die Erwartungen erfüllt !
Michael D Meek
Reviewed in the United States on September 28, 2023
I bought the three-pack of stepper motors for about the same price as two individually, AND they came with cables about eight inches longer that what were on my machine. I replaced a stepper (which was not the problem I was trying to fix,) then replaced the cable and, VOILA! It works! These steppers come highly recommended, and I left the new one in my machine because it was a perfect fit.
Michael D Meek
Reviewed in the United States on September 28, 2023
I bought the three-pack of stepper motors for about the same price as two individually, AND they came with cables about eight inches longer that what were on my machine. I replaced a stepper (which was not the problem I was trying to fix,) then replaced the cable and, VOILA! It works! These steppers come highly recommended, and I left the new one in my machine because it was a perfect fit.
Bruh
Reviewed in the United States on November 13, 2023
If you came here looking to replace the stepper on your Anycubic be aware that when you plug this stepper motor in you'll get nothing but a wiggle back and forth no full rotaion. even with the replacement wire. You'll need to find the correct cable pairings and rewire the cable. Google for more info.
Bruh
Reviewed in the United States on November 13, 2023
If you came here looking to replace the stepper on your Anycubic be aware that when you plug this stepper motor in you'll get nothing but a wiggle back and forth no full rotaion. even with the replacement wire. You'll need to find the correct cable pairings and rewire the cable. Google for more info.
Recommended Products
