Your cart is empty.
Your cart is empty.Mr. Macaroni
Reviewed in the United States on September 28, 2024
I recently got a WiFi 6 access point that supports PoE. The access point can do "up to" 2400mbps, so a simple typical run-of-the-mill gigabit PoE injector would not be even close to sufficient. This thing can handle it plus being future proof. I'm getting about the same ~1400mbps real-world speed that the AP can do when hooked up with an AC adapter. The PoE injector is definitely a bit on the bulky side, but that doesn't matter too much. One nice thing about a PoE injector is that you can hook it up somewhere out of the way. Overall, I think this is a pretty good PoE injector for multi-gigabit use.
Lon
Reviewed in the United States on September 20, 2024
I installed a new Pan/Tilt/Zoom Internet Protocol security camera that supports Power over Ethernet. I did not want to install a 120VAC outlet just for this camera, and I have maxed out the capacity of PoE devices plugged into my Network Video Recorder.There is a 120VAC power outlet about 45 feet from the camera, so I plugged this PoE injector into that outlet and ran a 50-foot Cat6A Ethernet cable from the injector to the camera. This little PoE injector was the perfect answer and has my new PTZ camera spinning and whirring with aplomb.Overall, works perfect, solid little block with thick AC power cord and two Ethernet ports; one for the network source and one with injected power for the PoE device. Working great.
Jeremiah
Reviewed in the United States on September 19, 2024
Most POE injectors on the market do not support the higher speeds and are limited to 100Mbps. This one is not limited that low and instead boasts a whopping 10Gbps. The injector feels solid and well made. I am using it in a security camera application and it provides plenty of power for my needs. This is a very good POE injector and I recommend this one over some of the other cheaper/slower ones on the market.
Byron Williams
Reviewed in the United States on December 26, 2024
I wanted to connect a sfp port on a mikrotik switch to a UniFi 7 AP to allow for full 2.5gbe uplink without losing Poe and this did the trick. The switch and AP are both registering at 2.5.
Benjamin Moody
Reviewed in the United States on October 30, 2024
Came in some simple cardboard packaging with AC power cable. I was getting the required PoE power just fine with this injector and data worked perfectly as well. No complaints! It's definitely a quality product worth the $35 at the time of writing.
T H
Reviewed in the United States on October 21, 2024
This PoE injector handled any network traffic I could throw at it without any quality degradation, though I have no way to test 10Gbs. For 4k cameras, this worked without a hitch for days on end, as long as I monitored it. It is great that it does not require an external DC power source, it takes 110V AC and provides the right voltage for PoE internally. The construction looks fine, not at all impressive with the plastic casing, but it looks adequate as this device did not get hot under use.
LLM
Reviewed in the United States on October 19, 2024
While I don't have a 10Gbps network, I can't verify the speed. The power portion works fine. I have had no problems with it powering POE cameras.
Grumpy Spud
Reviewed in the United States on October 13, 2024
This 10Gbps PoE+ Injector is like the muscle car of network accessories - strong, fast, and ready to rev up your devices. Compliant with IEEE802.3at/af POE standards, it delivers a punchy 30W for PoE+ or a respectable 15.4W for PoE, ensuring your gadgets stay juiced up over distances up to 100m. Think of it as the Thor's hammer of PoE injectors: powerful and reliable.During the inaugural test, it handled my IP cameras like a champ, delivering consistent power without breaking a sweat. It’s like having an electrical superhero guarding your network. The injector’s sleek design fits right in with my tech gear, and I half-expected it to start playing the Avengers theme every time it powered up.
Recommended Products
$69.99
$ 31 .99 $31.99