Your cart is empty.
Your cart is empty.4.0 out of 5 stars
- #114 in Powerline Network Adapters
Product Description
Interface detail
- The CAMERA Port: max 8W power consumption, the OUT Port: max 15W
- The POE input port: POE Mode A/B, 2 output ports: POE Mode A/B
- Max bandwidth :100Mbps
- Green LED: Indicate PoE Power Activity Status. Working status: Always on
- Yellow LED: Indicate Data Link Activity Status. Working status: Flashing
Excellent Compatibility and Safety
- Using hardware IEEE802.3af/at PoE chipset, it automatically powers up PD device with 4 steps (PD Detection -> PoE Classification -> Start Up -> Power ON). It allocates appropriate power to IEEE802.af/at PoE devices, and no power for non-PoE devices. It ensures high safety for PoE and Non-PoE devices
Georgyto
Reviewed in Mexico on February 14, 2025
Compro 2 y se ocupan con distancias de 100 y 200 mts para videovigilancia y operan bien
ASL
Reviewed in Canada on January 5, 2025
Works great but needs POE+ source to run two POE cameras. They do get warm to the touch if powering two cameras but nothing to worry about. I’ve installed them both indoor and outdoor and they work great.
Ben Ramsden
Reviewed in Australia on January 10, 2025
Linovision is a preferred supplier. We purchased this as a simple PoE switch. Cameras worked fine over http but rtsp failed until we adjusted our software “Live555 stream transport settings”. Very happy now. Support from Linovision was super fast and friendly.
Baljit
Reviewed in Canada on September 19, 2024
Tried other similar version this is the most stable to its competitors!
u2rec
Reviewed in Japan on February 16, 2024
PTZカメラとレコーダーをpoe接続で1本の配線で使えています。今の所これといったトラブルもなく安定して使えています。
Customer
Reviewed in the United States on March 2, 2023
I needed to add a camera to the garage but did not like the idea of running another wire to the switch. This device allows you to use an existing wire to add another camera. Apparently, the voltage coming from the POE switch is enough to support more than one camera. I'm very happy to have run into this extender.
Customer
Reviewed in the United States on February 11, 2023
I'm a network engineer of 30 years and tried this product on multiple POE products including Unifi switches. The lights never came on, the product never worked. For me it was a waste of money and time; I would recommend avoiding this product.
Matt M
Reviewed in the United States on January 31, 2023
Went thru several brands/models of these before I found this one that worked. Using it to power a PoE camera and also a second PoE to 12V adapter for an extra IR floodlight off the same network drop. Works great!
Christopher
Reviewed in the United States on May 8, 2022
Ordered two units, one was DOA. Other one works to power two ip cameras, but after a day both went offline. Had to reset Poe switch. Went offline again a day later.They offered replacement or refund with no hassle so I gave 4 stars for that.
Bought This Item
Reviewed in the United States on February 2, 2022
My POE switch has only one port available and total power wise its running 50% below max. Tested it with two Hikvision fixed lens cameras that pulled about 5 watts each. Power cycled, about six separate times, the POE LAN port that is connected to the IN on this unit (PoE Extender02), every time the NVR system reconnected both cameras without a problem. Didn't try to replicate rookie mistakes of running at max spec for this unit as it always is safe and saves time to run under specs, why? cause functionality is always the premium.
mpat
Reviewed in the United States on February 13, 2022
I needed to add a second POE camera in a location where I already had one. I really didn't want to run another Ethernet cable, so I purchased this to run both POE cameras off the one cable and it works! I was so happy that the POE could power this switch along with both cameras. Not only that, but there is about 150-200' of CAT5e cable between the primary POE switch and this switch - and it still works! Couldn't be happier.
John Bion
Reviewed in the United States on January 13, 2021
This is a fantastic product, easy installation and well worth time and savings of not having to install a new wire all the way back to the switch room. I used this to add an IP Camera out in the field and jumped off an existing camera out there, saved a lot of time and money. Thanks
Mike
Reviewed in the United States on August 19, 2020
This device works as advertised, it will take a single PoE line in and provide two PoE lines out. HOWEVER: make sure you mount this device where you can easily get to it. I have installed two of these units on separate projects, and in the event of power loss, they will not reset properly. Both ports turn on at the same time and neither one will grab an IP address. The only remedy I have found is to unplug one of the cameras, wait about five seconds, then plug it back in. At that point, both cameras will obtain IP addresses again.
Recommended Products