Your cart is empty.
Your cart is empty.Product Description
Adjust Camber Angle -3° to +3° Toe -2° to +2°
Adjust camber either positive or negative with the turnbuckle adjuster. Can be adjusted without removing from the vehicle
Effective protection
Made of heat-treated carbon steel to increase the hardness and strength of the metal, the bushing is made of polyurethane for a more direct feel and driving experience.
Feature
Made by high strength steel and durable Powder-Coated Finish，prevent rust and corrosion，Polyurethane rubber bushings and necessary hardware for installation are included.
Replacement
Can directly replace OEM arms on vehicles with stock ride or on vehicles that have been modified for performance. Wider range of camber adjustment suitable for street or track tuning
Richard Luce
Reviewed in the United States on September 27, 2024
They are very noisy and squeaky but worked to align my tires
Cristobal Corona
Reviewed in the United States on September 21, 2024
I purchased these to adjust the rear camber on my 96 Civic. The quality is okay for the price, but I didn’t expect to have to replace them after about five or six months of service. The driver side lost the bushing all together.
Juice
Reviewed in Canada on September 10, 2024
Not made right. Low QC part. TBD once installed... Finally installed and seems OK. I wanted to get "Stanced" out of them, however only achieved 4 degrees and maxed out. If you're looking to correct your camber this is good enough. If you want to get 5-6 degrees look elsewhere. I needed more! Rubbing and Scrubbing for life ;p
Dustin1226
Reviewed in the United States on August 4, 2024
Used these to get rear camber back in spec. Had almost 1.5 degrees of neg camber due to age on a 99 civic. Put these is and camber is a perfect 0.0.Could probably use these if you wanted to "stance" a car but I bought them to put it back in spec. Highly recommended 👌 👍 👏 💯
Angela
Reviewed in Canada on August 28, 2024
I bought these for my 1999 civic coupe, they did not sit flush against the body where your 2 bolts go in, I had to take a grinder and cut a little shoulder off on each tab that was just a tiny bit too big so that they would sit in the gap flush. They do their job good once modified a little
Eri Atlai Maciel Ozuna
Reviewed in Mexico on May 8, 2024
El material de la construcción aguanto pero los bujes no duraron ni dos semanas. No recomiendo
William
Reviewed in the United States on May 18, 2024
half price of autozone
Raptor
Reviewed in the United States on October 13, 2024
The media could not be loaded.
Roberto
Reviewed in Mexico on September 25, 2023
Excelente calidad y fácil instalación
Juan Rodriguez
Reviewed in the United States on July 26, 2023
Justo lo que necesitaba para mi honda crv 1998
Adam
Reviewed in the United States on June 16, 2023
I specifically bought these due to steel construction advertised and not wanting questionable aluminum used for suspension bits.Well, the bodies on these units are aluminum BUT they are also much higher quality than I was expecting from cheapies from Amazon.They come dry, so you will want to disassemble and lubricate the bushings.So I feel a little lied to but also with an ultimately higher quality than I expected soooo overall good things?
The Buyer
Reviewed in the United States on November 11, 2023
overall I'm satisfied with these. the flange could have been better machined but fits in the cup once bolts are tightened. as for the trailing arm end it is a bit smaller but just tighten the bolt it'll be fine unlike other buyers complaining it's too small. what they expect it's aftermarket not oem but anyway these were good I've seen other camber arms worse than this. and don't forget to measure then tighten the end nuts to lock in the adjustment I also put some anti sieze where needed in case to prevent locking up.
Dalton kilbreath
Reviewed in Canada on December 8, 2022
Seem super strong haven’t installed yet
Recommended Products