AMAZING arm for an ultrawide! I have a 34in ultrawide that I previously had on a dual mount that kept sinking down after a while no matter how much I tightened the tension. I just set up the arm and this thing is strong. It was very easy to piece together and actually comes fully apart which makes it much easier to transport if you needed to move. Out of the box the tension was set really tight which made mounting the monitor quick and painless. After loosening it a bit, the arm is super easy to maneuver and allows me to easily push it out of the way if need be. The actual arm of the stand has a much smaller profile than my previous arm which saves my poor wall from getting banged up.By far though the most impressive thing to me that just has so much attention to detail, THERE IS AN ATTATCHMENT AT THE BACK OF THE BASE TO HOLD THE ALEN KEYS. I genuinely had my jaw drop when I realized this, its important to keep them to be able to adjust the tension so actually having a spot where they belong and are totally out of the way was so smart!

Great bracket fitted a 34 curved screen too

I use this with an LG 38" ultrawide monitor. It handles the weight easily, and I can move the monitor around as much as I want.The clamp system is a nice improvement from others I've used because you put it in place then tighten the clamp from above using an Allen wrench. That helps if you're short on space to maneuver below the desk. The arm then slides onto the post and covers the Allen socket.

great for 32gk805gb, really easy set up and easy to follow manual. at this price point i can't complain much

Muy buena opcion, me ayudo mucho para montar un Samsung Q8, me ayudo a poder girarlo en vertical, super!

Using this with a LG C3 42" and it works fantastic. Once everything was tightened I could tell how rigid it was and was confident that nothing would tilt or fall. Make sure to keep everything under the weight limit if you are buying this for a big monitor/tv as you'll need an extra adapter for the LG C3 that adds some weight.Pros: simple setup, sturdyCons: cable management is kind of an afterthought, not good

I bought this based on other reviews. The only known mount option for the G9 Odyssey costs $400. I bought this mount as opened box for $70 making it quite the cost difference between the two choices. For other odyssey owners out there this mount will cover your needs, the reviews are accurate. However you will need to follow a couple quick steps.Before mounting the monitor, assemble the arms together on your desk. Be careful not to lose the little metal tabs between the arm shrouds they fall out easily when you take the arms apart later. Next take the provided tool and spend a minute rotating the middle of the arm adjustment screw towards the + symbol. You will question if the bolt will fall out from the amount of turns needed. Doing this is required or the gas piston won't hold up the monitor! Next the problem child of this mount is the vertical up/down tilt at the end of the arm. The included bolt won't hold the odyssey up and its a pain to deal with when the monitor is mounted. So trash it. Now take the heavy piston arm to your garage or hardware store. I found that a 13mm bolt head fit the hole and threads. Add a washer on both sides followed by a castle nut. You will need two 13mm wrenches or socket wrench to tighten the new bolt down, it won't take much pressure. Next reattach the arm onto the mount, without the monitor. Use a level or eyeball it to tighten it down evenly leaving the tilt at 0 degrees. Though it might be best to tilt it back or upwards 10 degrees due to how the arm mounts into the monitor bracket. Lastly mount the back plate to your monitor and attach the piston arm. If you're mildly strong pick up the monitor with the screen facing you then drop it into the mount on the desk. Really it's a two person job! If the monitor is tilted incorrectly you are going to need a friend to hold it or adjust it as you tighten/loosen the new bolt again, a major pain. I had it sitting on the desk and it was a thirty minute fight trying to get the tilt right. Turns out the mount itself on the arm tilts forward about 10 degrees making the monitor tilt down a little. Ughh just bring a friend the tilt adjustment is an all or nothing ordeal. Too Loose the monitor flips down and too tight it won't budge. It was terrible juggling this thing with tools in hand with this heavy thing... And that's all the extra work you need to do! Tighten the piston adjustment bolt towards the + and buy a new bolt for the vertical tilt.Oh pro tip: test without the monitor attached sitting down and see if you like the placement. Originally I had mine mounted center on the desk and well that didnt work at all. Now its off center to the right. Also use the included package foam to check clearences. I balanced the foam on the end of the arm and it worked great as a reference piece.As for mount itself, the mounting plate included does fit the odssey's metal cup plate, use the included black screws with a screw driver. Just be sure to tighten "everything" down. Don't skimp on this or locktight if you have it. Overall everything is thick aluminum or cast aluminum so its solid metal. The pressure plates are thick steel and well painted. Everything fit together without any extra work. The desk pressure plate is only held on top of rear vertical bolts by gravity. Its very jank but works the part when tightened. The plastic cable covers were a pain but doable.The biggest gripe I have is the janky L bracket. There are four thick screws holding it together and its not flush or a perfect 90 degrees in the back. So if your desk is against a wall like mine, it won't be the most ideal... I didnt add the plastic cover to save on an extra half inch clearence against the wall. I really dislike the screws on the L bracket. I had two of them strip out with mild pressure. In the future I'm going to redrill the holes and add proper bolts to secure it.The extra added effort was worth saving $300 over the other expensive option. I'll update this review if anything changes. For better or worse.

I have seen a few reviews for this arm that seem to suggest that this arm cannot support a 49" monitor, and others that say it can, and still others that say it requires modification to do so. I can confirm that it works without modification for specifically the 49" S95UA Super Ultrawide, which comes in at a whopping 32.2 pounds.Tilt and swivel can be as tight or as loose as desired, simply tighten the bolt on the head that does the tilting/swiveling. Up/down adjustment of the arm even has some headroom, I adjusted it to be as strong as possible initially and it was too much; the arm would always move back into its highest position. I actually had to tune it down to get it just right, so that it would stay at whatever height I moved it to.Really not sure what to make of the reviews that say it cannot work for such heavy monitors. The adjustment for the gas spring is left for tighter, right for looser; maybe that's where the confusion is coming in? It's stamped right into the metal though, sort of hard to miss. Funnily enough this is almost a carbon copy of a dual-arm mount I bought awhile back, just a couple details (besides this being a single arm) are different. They were from two different "manufacturers", so I assume it's all made by the same Chinese manufacturer and gets re-branded by whomever sells them.Just to summarize, this arm handles my 49" 32.2 pound monitor just fine. It actually had some headroom for extra weight. It can be as tight or as loose as desired for tilt/swivel. Easy to adjust, and I did not need the instructions for assembly. It's pretty self explanatory. Be aware, if you are buying the exact same monitor I did (49" S95UA Super Ultrawide from Samsung) that you will need an extra set of screws for the VESA mount. The arm includes a set of 4, but the monitor does not include the extra set you will need for their adapter bracket. Tools for adjustment and assembly are included, but having an actual screwdriver is easier.