Lo compré para montar un segundo monitor en mi escritorio. Muy fácil y rápido ensamble. Ocupa poco espacio y no se necesita taladrar. Además su movilidad es excelente.

As described

Does exactly what’s required. Great value

Fit properly, fit into the vesa mount of my monitor, holds it sturdily. Looks good, has the ability to change angles and direction. Great range of motion and ease of use.

For the price, I’m pleased with it.Overall, it’s a sturdy stand with quality machining. All the screws went in easily, poorly machined products have crooked holes or bad threads. The mount base comes with 2 types, standard mount for a desktops surface. The other one is for desktops with monitor holes/cabling drilled through them. All the parts are heavy gauge and I encountered no difficulty during assembling.There seems to be a tension screw for the tilt feature. I had to tighten the screw that holds the tilt joint together because out of the box, the monitor flopped forward hard. I had to be mindful while mounting it to the main arm so it wouldn’t slam into my glass desktop.The 2 arms that allow you to move the monitor forwards and back, left and right were a little stiff, I loosened the screw a bit on the main arm, at the pole. That seemed to be all that was required. I tried to loosen the bolt where the 2 arms meet, and it wouldn’t budge. I didn’t force the issue.The instructions were adequate for assembly without covering anything else, like adjusting the tilt bolt for the weight of the monitor.So, while I think this was a good mount for the investment, there are tradeoffs to mention.I’m accustomed to swinging my monitors upward and dusting underneath them. Height is fixed by a screw on this one.I was struggling to install the monitor cables when I realized you can tilt the bottom toward you until the top or the monitor hits the pole, or, until it’s sitting nearly flat like a table. Elevated several inches above the desktop. I consider this a Pro / Con feature.Where the arm ties into the VESA mount, the fit is a little sloppy. It’s not a safety concern but I can wiggle the monitor backwards and forwards at the outer edges “About ¾ inch “before feeling any resistance from the mount. Same goes for tilting. I don’t see this as much of an issue. Normally, I don’t foresee any outside forces acting in the monitor to create a problem. However, there’s room for improvement. The rest of the machining seemed steller.I have multiple computers in different rooms. 32” monitors are used as primary monitors with 32” to 23” as secondaries.I like mine roughly 1” above the desk. That places the top of the monitor at my eye level and the ideal viewing angle.I have fully articulated, hydraulic mounts on most of my monitors. Nice ones for large heavy monitors run $75 to $100 and up. I paid $36 for this one. The……… WALI Monitor Arm Mount for Desk, Single Extra Tall Computer Desk Mount, Monitor Bracket Mount Stand Single, up to 32 inch, 22 lbs (M001XL), Black.Amazon lumps the reviews of similar products together, so I specified which mount I purchased.I’m using this one on a glass desktop, I’m attaching it to the same point I constructed from wood for a different mount. It didn’t lower the monitor low enough either. So, the top of that mounting point is 4” lower than the surface of the glass top.Despite being that low, I didn’t actually need the 32” pole / monitor mount, the 16” model would have worked.There’s still 2” of pipe available above the arm. The 32” was on sale & I didn’t know if the 16” would suffice. The pole is a screw together 2 piece. I unscrewed / removed the other pole as it looked out of place in my dual computer setup.That leaves a hole in the top of the pipe / mount. I wish they included a cap for that. The top pipe has a cap but of a different diameter.I’d like to give it 4 ½ Stars but Amazon won’t let me. I’ve got to go with 4.Height adjustments with heavy monitors and an Allen wrench can present a challenge, it’s the nature of the beast and I won’t give it 5 stars for a few reasons. The sloppy VESA mount and loose tilt motion. No instructions that cover that, or if I was supposed to loosen the arm at the pole to improve motion.I would recommend this mount to others.

This is the third WALI desk mount solution I've purchased and it's the third because their products work. Assembly was fast and easy. Installing the mount on the desk was simple.Due to the height of the mounting position and the adjustment being a little primitive, it was easier to dial in the monitor positioning with a second person to stabilize the monitor so I could make fine adjustments. I will also note that it is a little shaky and a creative reinforcement would benefit a very permanent installation; because my desk is motorized I can't brace this mount to the wall.That said, I'm quite pleased with the result and the price was fair for the value and relative quality compared to other options.

Mi serviva proprio un prodotto così, senza dover bucare da nessuna parte!!! Super

Great item, it's quite robust, made with strong metal.

The Wali Single Monitor Desk Mount works better than I expected.First, the basics. The mount comes well packed and the instructions are very simple to understand. There is so little assembly required that the instructions are almost not needed. Assembly and installation can be done in less than ten minutes (not including cable management if you choose to use that feature). Adjusting everything is easy. Overall quality of the parts and the assembled product are quite good.I have two monitors that I wanted to mount on a flat desktop. I needed to be able to get the monitors right next to each other and still have the desk flat against the wall. Most double monitor stands will not allow for this unless your monitors are the perfect size for the spread of the arms. The movable arms will usually flex toward the wall if you want the monitors to be edge-to-edge with each other. The result is the desk having to be offset from the wall to accommodate this. By using two single monitor stands, I am able to move the posts to positions that allow the arms to be extended in such a way that everything is flat with the wall.The other frequently stated issue with most monitor stands is that the arms have hydraulic pistons and/or springs to deal with the weight of the attached monitors so they are easy to move up and down. These pistons and springs are often of poor quality and either fail quickly or don't work as expected from the get-go.This is not a problem with the Wali Single Monitor Desk Mount. The arm is solidly attached to the 16" pole and only moves up and down by loosening the arm mounting and sliding the arm up or down on the pole. The arm, once set to the desired height, can be move forward, backward, side-to-side and tilt. This makes for a much sturdier setup with no pistons or springs. This system works very well, since I (and I think most people) have little need to move a monitor up or down after the initial installation.I leave the included Allen wrench stuck in one of the vertical facing screws behind a monitor so that it is always handy but out of sight. If I do need to move the monitors up or down, the tool is right there.I will buy two more of these for my wife's desk.