Your cart is empty.
Your cart is empty.From the manufacturer
Pre-Installation
- Secure firearm or riflescope in a clamping device.
- Find the center of travel on your magnification ring and place a mark at the center point as a reference.
- Scopes with an illumination knob (1-A): Guide the ring over the eyepiece, gently spreading the ring around the illumination knob. Slide the ring past the magnification ring onto the riflescope tube.
Ball/Socket Assembly
- Apply one drop of lubricant to the ball of the ring. (2-A)
- Slide the ball into the socket of the lever (2-B). Gently 'work' the lever onto the lubricated joint until the connection is flush.
- Note: Because of precise tolerances and variances in the thickness of the anodized coating, the connection may be exceptionally tight.
Installation
- Slide the assembled switchview onto the magnification ring and align the lever with your marked reference point.
- Insert the Allen Screw through the unthreaded hole in the lever and into the ring (3-A). Tighten to 5-7 in/lb with the Allen Wrench.
- Caution: Do not over-tighten. Over-tightening may cause damage to the switchview or riflescope.
Testing
- Test to ensure the switchview lever is in the best position for you.
- To adjust, simply loosen the screw and reposition the lever to a more comfortable position. Then, retigthen the screw and test the new position.
Customer
Reviewed in the United States on March 7, 2025
Works as it should. Mounted on razor 1-6
Aaron C.
Reviewed in the United States on March 5, 2025
I bought this for being able to quickly adjust rifle scope magnifications. With this setup you can easily adjust the range with a fingertip. Without this you have to wrap your fingers around the rifle scope magnification ring and twist to adjust. It makes things a little easier without having to take your eyes off the item you are sighted in on while adjusting.
John
Reviewed in the United States on February 20, 2025
Throw handle was easy to install and is solid so no issues.
Customer
Reviewed in the United States on July 12, 2024
Installs easy. Works great. Good quality. Good buy.
Wesmantooth
Reviewed in the United States on August 17, 2023
These things are expensive, and i never could understand why... until now. Such a handy tool to make a vortex scope even more great! Solid and well build, functional and ergonomic. Just be very careful and follow instructions. It's easy to over tighten the small screw and bend the very fragile piece. It doesn't need to be as tight as you think! If you are on the fence, just buy it!
Sauli
Reviewed in France on April 29, 2022
Article signalé défectueux par plusieurs acheteurs. Étonnamment le vendeur continue de le distribuer….
AZprof1
Reviewed in the United States on December 24, 2021
I bought a a no name 3D printed a while ago for another of my Vortex scopes and it's OK. These are genuine Vortex and great fit. Be nice if a little bit less expensive but you get what you pay for. Bought 2, 1 each for my new hunting scopes. Vortex magnification adjustment a bit tight so the throw lever makes a welcome addition. Works very good.
Sora
Reviewed in Japan on December 29, 2020
注文したらちゃんと実物のSV-4が届きましたが、自分が持っているStrikeEagleにつけてみたらフォーカズリングの直径よりが２ｍｍ太いです。ズームインすると約横幅4mmぐらいの遊びがあり、ガタガタしていました。最初はそういう仕様だと思いましたが、アメリカ人のブログやデビュー見たらどうやらこの商品は以前流通していたStrike Eagle 1-6x24 (Gen1)しか対応していないことが分かりました。2019年以後生産されたフォーカズリングは少し小さくなった故、加工しないとピッタリ光学につきません。ガタガタのまま使うとリングとレバーにお互い傷ついてしまうので早めにはずすほうが良いです。が、VORTEX公式サイトが未だに情報修正していないのがなかなかアメリカ人っぽくて......
Vadim
Reviewed in France on July 14, 2019
Parfait pour l optique
tominjax
Reviewed in the United States on December 27, 2017
I have been looking for a throw lever for my Crossfire II 1-4x24mm for about a year. I found it upsetting that Vortex does not offer one for the Crossfire line and my only other option was one of the plastic "universal" throw levers.After reading one of the other reviews where someone put electrical tape between the throw lever and magnification dial, I decided I would give this a chance.The throw lever comes in two pieces, the throw lever and the mounting ring. One end on the ring fits together like a puzzle piece and the other end has a screw to tighten it down. I took the throw lever and filed away about 1mm of material on the screw end. I did a small amount, checked it and repeated until it was just right. Mounted you can't even see any of the bare aluminum. It's rock solid and works as expected.It's way over priced, but a must have for fast magnification changes.
Papa Gator
Reviewed in the United States on September 15, 2016
Great add on that makes switching magnification much easier on close to mid range scopes where the quick adjustments are needed. Especially on cold mornings out hunting when everything is more stiff. When you have a 2-5 second window on the game, you don't want to be making a bunch of noise and fumbling around trying to get the right magnification for the distance you're shooting, and this makes a world of a difference. My only gripe is it is very expensive for what it is. Small and very light it nice, but at almost $60, I feel it should be half the price. Nonetheless, it is a great item to have on an optic, and if you can shell out the money, I'd get one.
Client d'
Reviewed in Canada on April 30, 2016
ce que je trouve dommage c'est que la piece qui coute au depart 79.00dollards me revienne a 186,00 dollards c'est une tres grande difference pour cette petite piece
Recommended Products
$24.99
$ 11 .99 $11.99